background image

32

   

Installing 10krpm Hard Disk Drives on a Kayak XU

Installing 10krpm Hard Disk Drives on a Kayak XU

The HP Kayak XU Series 0301 and 0303 PC Workstation contains seven 
mass storage shelves:

Two internal mass storage shelves (3.5-inch wide):

Top internal shelf. 

A 1-inch high hard disk drive can only be

installed in this shelf. This could be either a 4.5 GB or 9.1 GB low
profile hard disk drive.

Lower internal shelf. 

A 1.6-inch high hard disk drive can be

installed this shelf. It can also shelve the low profile (1-inch in 
height).

Five front-access shelves:

To ensure that hard disk drives are properly installed and cooled, 
you should only install hard disk drives up to 1-inch in height and 
of a speed equal to or less than 7.2 krpm in these shelves. Because 
there is not enough air flow in the front-access shelves, 10 krpm 
hard disk drives cannot be installed.

How many 10 krpm hard disk drives can be installed in the
internal shelves on the HP Kayak XU Series 0301 and 0303 
PC Workstation?

You can install up to two (2) 9.1 GB Low Profile (LP) SCSI 
hard disk drives in the internal shelves.

Two internal mass storage 
shelves (3.5-inch wide).
Upper shelf: 1-inch high
Lower shelf: 1.6-inch high

Two 3.5-inch wide 
low-profile shelves

Three 5.25-inch 
wide 1.6-inch front-
access shelves, but 
only support 1-inch 
high hard disk drives

Содержание Kayak XU 03xx













































Отзывы: