manualshive.com logo in svg

HP J8697A, Руководство по установке

Поделиться
Скачать
HP J8697A Скачать руководство пользователя страница 47

39

Specifications

Mode Conditioning Patch Cord

The following information applies to installations in which multimode fiber-
optic cables are connected to a Gigabit-LX port or a 10-Gigabit LRM port. 
Multimode cable has a design characteristic called “Differential Mode Delay”, 
which requires the transmission signals be “conditioned” to compensate for 
the cable design and thus prevent resulting transmission errors.

Under certain circumstances, depending on the cable used and the lengths of 
the cable runs, an external Mode Conditioning Patch Cord may need to be 
installed between the Gigabit-LX or 10-Gigabit LRM transmitting device and 
the multimode network cable to provide the transmission conditioning. If you 
experience a high number of transmission errors on those ports, usually CRC 
or FCS errors, you may need to install one of these patch cords between the 
fiber-optic port in your switch and your multimode fiber-optic network 
cabling, at both ends of the network link. 

The patch cord consists of a short length of single mode fiber cable coupled 
to graded-index multimode fiber cable on the transmit side, and only 
multimode cable on the receive side. The section of single mode fiber is 
connected in such a way that it minimizes the effects of the differential mode 
delay in the multimode cable.

10-Gig ER

single mode fiber

N/A

2 - 40,000 meters

CX4 Media Converter

12-strand female-female multi-
mode fiber MPO ribbon cable 
with MTP connectors, in a 
crossover (key up/key up) 
configuration

150 MHz*km

500 MHz*km

2000 MHz*km

1 - 50 meters

1 - 100 meters

1 - 300 meters

1

  Cat 6 cabling requires TIA TSB-155A testing for 500 MHz operation and ANEXT.

2

 

For distances less than 20km, a 10dB attenuator must be used. For distances between 20km and 40km, a 5dB attenuator

  must be used. Attenuators can be purchased from most cable vendors. 

Table 4.

Technology Distance Specifications(Continued)

Technology

Supported cable type

Multimode fiber

modal bandwidth

Supported distances

Содержание J8697A

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды