manualshive.com logo in svg

HP J8697A, Руководство по установке

Поделиться
Скачать
HP J8697A Скачать руководство пользователя страница 26

18

Installing the Modules

Installing the Modules

Overview

Before installing any module, ensure you have loaded the most current 
software for that module onto your switch, see 

page 3

 for the V2 modules 

software version, and see 

page 6

 for the previous module software versions. 

You can install any of the modules into any of the HP networking chassis zl 
switches that have compatible module slots. 

HP E5400 zl Switches:

■

E5406 zl and all related bundles

■

E5412 zl and all related bundles

HP E8200 zl Switches:

■

E8206 zl and all related bundles

■

E8212 zl and all related bundles

“Hot Swap”

Notes

The mini-GBICs can be “hot swapped”. That is, they can be installed or 
removed after the Module is installed in the switch and the module is receiving 
power, see 

page 21

.You can “hot-swap” one module for another; that is, replace 

one module with another while the switch is still powered on, without inter-
rupting the operation of the rest of the switch ports, see

 

page 29

.

 You may have 

to reconfigure the switch if the modules are not the same type, check your 
configuration.

You can install the modules into the switch either with the switch powered on 
or off. The following procedures assume the switch is powered on.

1.

Install the modules in a switch slot (

page 19

).

If you have installed any modules into slots that were previously occupied 
by a different type module, you need to reset the switch.

2.

If you are using the zl Module that supports mini-GBICs, install the mini-
GBICs in the module. You can install the mini-GBICs before or after 
installing that module into the switch (

page 21

).

3.

Verify the modules are installed correctly (

page 23

).

4.

Connect the network cabling (

page 25

).

5.

Verify the network connections are working properly (

page 27

).

6.

Optionally, customize the configuration for the modules’ ports (unless 
the default port configuration is satisfactory for your network application 
(

page 28

)).

Содержание J8697A

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды