HP J4861A Скачать руководство пользователя | Manualshive

Страница: 22 / 94

background image

Installing the Series 4100gl Switches

Installation Procedures

Installing the Series 4100gl

Sw

it

ches

Installation Procedures

Summary

Follow these easy steps to install your switch. The rest of this chapter provides
details on these steps.

1.

Prepare the installation site (

Ensure the physical environ

ment into which you will be installing the switch is properly prepared
including having the correct network cabling ready to connect to the
switch, and having a good location for the switch.

some installation precautions.

2.

Install switch modules (

The Series 4100gl Switches have

four or eight universal slots for installing any of the HP ProCurve Switch
gl modules. The Switch 4108gl Bundle has three 24-port 10/100-TX gl
Modules and one 3-port Transceiver gl Module preinstalled, and the
Switch 4148gl has two 24-port 10/100-TX gl Modules preinstalled.
Depending on where you will install your Series 4100gl switch, it may be
easier to install the modules first. The modules are “hot swappable”
though, so they can also be installed and removed after the switch is
powered on.

Note: Make sure you use only HP ProCurve Switch gl Modules in
your Series 4100gl Switches.

3.

(Optional) Install second power supply (

The Series 4100gl

Switches have a slot in the back for installing a second, load-sharing
power supply. If you have purchased this supply, it may be easier to install
it before mounting the switch.

4.

Verify that the switch passes self test (

This is a simple

process of plugging the switch into a power source and observing that the
LEDs on the switch’s front panel and on the modules show correct
operation.

5.

Mount the switch (

).

The Series 4100gl Switches can be

mounted in a 19-inch telco rack, in an equipment cabinet, on a wall, or on
a horizontal surface.

Note that there are some limitations to the wall

mounting orientations that are supported.

Please see the installation

details for more information.

6.

Connect power to the switch (

Once the switch is mounted,

plug it in to the nearby main power source.

2-2

«
...
20
21
22
23
24
...
»

Содержание J4861A































































































Отзывы:

Нет отзывов

Похожие инструкции для J4861A

Бренд: 4O3A Страницы: 2

Бренд: eao Страницы: 2

Бренд: eao Страницы: 2

Бренд: G&D Страницы: 80

Бренд: Black Box Страницы: 44

Бренд: Pulsar Страницы: 5

Бренд: VigilLink Страницы: 24

Бренд: Gefen Страницы: 31

Бренд: asas Страницы: 25

Бренд: NETGEAR Страницы: 2

Бренд: DeviceWell Страницы: 32

EPS-1XPB-1XPL-M1-24V

Бренд: Larson Electronics Страницы: 2

MMAC-Plus 9H421-12

Бренд: Cabletron Systems Страницы: 12

GIGAswitch GSR-16

Бренд: Cabletron Systems Страницы: 346

XS-S1920 Series

Бренд: Ruijie Страницы: 51

Бренд: Pilz Страницы: 41

Бренд: Encore Страницы: 1

Бренд: Rose electronics Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды