HP J4861A Скачать руководство пользователя | Manualshive

Страница: 25 / 94

background image

Installing the Series 4100gl Switches

Installation Procedures

1. Prepare the Installation Site

Cabling Infrastructure

Ensure the cabling infrastructure meets the necessary network specifications.
See the following table for cable types and lengths, and see appendix B,
“Cables and Connectors” for more information:

Table 2-1.

Summary of Cable Types to Use With the Switch

Port Type

Cable Type

Length Limits

Twisted-Pair Cables

10/100/1000Base-T

For either 10, 100 Mbps, or 1000 Mbps
operation:

Category 5 or better, 100-ohm UTP or shielded
twisted-pair (STP) balanced cable. For
1000 Mbps (gigabit) operation, Category 5E
cabling or better is recommended.

100 meters

Note:

The Switch 2800 Series devices are

compatible with the IEEE 802.3ab standard
including the “Auto MDI/MDI-X” feature,
which allows use of either straight-through or
crossover twisted-pair cables for connecting
to any network devices including end nodes,
such as computers, or to other switches, hubs,
and routers.

Note:

For 1000 Mbps operation, all four wire

pairs are used for data transmission, therefore
PoE is not supported for 1000 Mbps operation.

Sw
itc
hes

Installing the Series 4100gl

2-5

«
...
23
24
25
26
27
...
»

Содержание J4861A































































































Отзывы:

Нет отзывов

Похожие инструкции для J4861A

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 2

xStack DGS-3612G series

Бренд: D-Link Страницы: 546

xStack DGS-3400 Series

Бренд: D-Link Страницы: 326

xStack DGS-3612G series

Бренд: D-Link Страницы: 493

xStack DGS-3400 Series

Бренд: D-Link Страницы: 540

DXS-3326GSR - xStack Switch - Stackable

Бренд: D-Link Страницы: 354

S5500-SI Series

Бренд: H3C Страницы: 130

S5500-EI series

Бренд: H3C Страницы: 19

S5500-EI series

Бренд: H3C Страницы: 91

S5500-EI series

Бренд: H3C Страницы: 24

S5500-EI series

Бренд: H3C Страницы: 69

S5120-SI Series

Бренд: H3C Страницы: 4

S5120-SI Series

Бренд: H3C Страницы: 209

S5120-SI Series

Бренд: H3C Страницы: 70

S5120-EI Series

Бренд: H3C Страницы: 32

Бренд: H3C Страницы: 83

Бренд: H3C Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды