HP J4861A Скачать руководство пользователя | Manualshive

Страница: 29 / 94

background image

Installing the Series 4100gl Switches

Installation Procedures

3. (Optional) Install Second Power Supply

A second, load-sharing redundant power supply (HP ProCurve Switch gl/xl
RPS, HP J4839A) can be installed in the back of the switch. To provide true
redundancy, this second power supply should be connected to a different AC
power source from the other supply. Then, if one AC power source fails, the
switch will continue to run. Each supply provides enough power to operate a
fully loaded switch, so even if one fails, the switch will continue to operate
normally.

Install the second power supply into power slot number 2 as shown in the
illustration on the next page.

The slot cover can be removed with either a flat-bladed or Torx T-10 screw-
driver. Retain the slot cover for future use.

C a u t i o n

The switch power supplies

are

hot swappable; they can be installed while the

switch is receiving power from the supply in the other slot. But, as indicated
by the caution statement on the power supply, the supply

must not be

connected

to AC power before being installed.

Sw
itc
hes

Installing the Series 4100gl

��

�

��

�

��

��

For safety and proper switch cooling, if either of the power supply slots are
not being used, make sure to attach the cover plate over the slot. Please see
the Installation Precautions on

for more information.

For installation details, see the instructions in the manual that comes with the
power supply.

2-9

«
...
27
28
29
30
31
...
»

Содержание J4861A































































































Отзывы:

Нет отзывов

Похожие инструкции для J4861A

Бренд: Qlogic Страницы: 135

SANbox2 SANbox2-64

Бренд: Qlogic Страницы: 224

Бренд: Rack World Страницы: 4

dominion kx III

Бренд: Raritan Страницы: 6

Бренд: Raritan Страницы: 5

DOMINION KSX II

Бренд: Raritan Страницы: 7

Бренд: Raritan Страницы: 2

Бренд: RDL Страницы: 4

Бренд: protech Страницы: 4

Бренд: N-Tron Страницы: 5

Бренд: LevelOne Страницы: 17

Бренд: Gefen Страницы: 56

Бренд: Comm-Tec Страницы: 48

Бренд: Lightwave Страницы: 53

Бренд: H3C Страницы: 77

Бренд: Cabletron Systems Страницы: 56

Бренд: A-Neuvideo Страницы: 16

Бренд: Blue Sea Systems Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды