HP E2470A Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 71

background image

To connect the termination adapters

The logic analyzer probes must be terminated for correct operation.

The nonterminated connectors, P1 through P7, must be probed by using
either the General Purpose probes (shipped with the logic analyzer) or the
100 kOhm Termination Adapters (HP part number 01650-63203).

•

Align the key on the male end of the termination adapter with the slot
on the connector of one of the logic analyzer cables. Push the
termination adapter into the connector.

•

Connect the female end of the termination adapter to the
preprocessor interface.

Connecting the Termination Adapter

Using the flex adapter

The HP E3445A flex adapter is designed to relieve mechanical stress and to
provide a degree of freedom between the probe adapter and the
preprocessor.

Setting Up the Preprocessor Interface Hardware

To connect the termination adapters

1–8

«
...
13
14
15
16
17
...
»

Содержание E2470A








































































Отзывы:

Нет отзывов

Похожие инструкции для E2470A

ACS880-01 Series

Бренд: ABB Страницы: 238

Бренд: Taylor Made Страницы: 2

Бренд: York Fitness Страницы: 18

Бренд: Safco Страницы: 2

Бренд: Omni Страницы: 193

ImageQuant LAS 4000

Бренд: GE Страницы: 86

Бренд: GE Страницы: 160

Бренд: GE Страницы: 134

Бренд: Modulate Страницы: 2

Бренд: CAMAG Страницы: 40

Бренд: Taylor-Wharton Страницы: 25

Бренд: i-CAT Страницы: 96

Бренд: ICP DAS USA Страницы: 45

Бренд: Laser Страницы: 2

Бренд: Lars Thrane Страницы: 50

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: KCI Страницы: 2

Бренд: KCI Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды