HP E-MSM310 Скачать руководство пользователя

Страница: 159 / 210

Local mesh

Radio configuration

7-7

Radio configuration

Simultaneous AP and local mesh support (single radio)

A single radio can be configured to simultaneously support wireless users and one or more

local mesh links. Although this offers flexibility, it does have the following limitations:



The total available bandwidth on the radio is shared between all local mesh links and

wireless users. This can result in reduced throughput if lots of traffic is being sent by both

wireless users and the local mesh links. You can use the QoS feature to prioritize traffic.



It limits you to using the same radio options for both wireless clients and local meshes.

A more effective way to handle this is to use a multi-radio AP. This allows one radio to be

dedicated to wireless users and another to local mesh links. Each radio can be configured

optimally according to its application.

Simultaneous AP and local mesh support (dual radios)

Two radios can be enabled at the same time on a local mesh profile. This enables the node to

search for a master (or alternate master) on both radios. Once a master is found and the link

is established on one radio, the other is used to create downstream links. This greatly

improves throughput over single-radio deployments.

Using 802.11a/n for local mesh

It is recommended that 802.11a/n in the 5 GHz band be used for local mesh links whenever

possible. This optimizes throughput and reduces the potential for interference because:



Most Wi-Fi clients support 802.11b or b/g, therefore most APs are set to operate in the 2.4

GHz band. This frees the 5 GHz (802.11a/n) band for other applications such as local

mesh.



802.11a/n channels in the 5 GHz band are non-overlapping.



802.11a/n provides increased data throughput, providing a

fat pipe

for traffic exchange.

The main limitations in using the 5 GHz band are:



Since the same radio options must be used for both wireless clients and local mesh links,

support for 802.11b/g clients is not possible on APs with a single radio.



The 5 GHZ band has a shorter reach when compared to the 2.4 GHz band. This could be a

factor depending on the distance your links must span.

Maximum range (ack timeout)

This is a global setting that is configurable on the

Radio

page when the

Operating mode

set to

Local mesh

. It fine tunes internal timeout settings to account for the distance that a

link spans. For normal operation, it is set to less than 1 km.

Содержание E-MSM310



















































































































































































































Результаты поиска

Содержание E-MSM310

Отзывы:

Похожие инструкции для E-MSM310

Бренды по названию

Популярные бренды

HP E-MSM310, Руководство по управлению и настройке

Результаты поиска

Содержание E-MSM310

Отзывы:

Похожие инструкции для E-MSM310

Бренды по названию

Популярные бренды