HP CC487-91209 Скачать руководство пользователя страница 32

Страница: 32 / 168

Set the JBIG compression mode

Enabling JBIG compression can reduce phone-call charges by reducing fax transmission time and is,

therefore, the preferred setting for shorter faxing times. However, JBIG might cause compatibility

problems when communicating with some older fax machines, in which case you might need to

disable it.

NOTE:

JBIG compression only works when both the sending and receiving machines have JBIG

compression.

To enable or disable JBIG compression, perform the following steps.

On the control panel, scroll to and touch the

Administration

icon to open the Administration

menu.

Scroll to and touch

Initial Setup

Scroll to and touch

Fax Setup

Scroll to and touch

Fax Send Settings

Touch

JBIG Compression

to see the settings.

Touch

Enabled

(default) to enable JBIG compression, or touch

Disabled

to disable JBIG

compression.

Change the sharpness setting

The Sharpness setting specifies the sharpness that the scanner uses when the product scans your

original. Sharpness enhances the edges of the original so that faint or fine text and graphics are

reproduced more sharply. Increasing sharpness increases resolution which also increases

transmission time.

On the control panel, touch the

Fax

icon to display the Fax screen.

Scroll to and touch

More Options

Scroll to and touch

Image Adjustment

Under the

Sharpness

heading, touch the left arrow to decrease the sharpness or touch the right

arrow to increase the sharpness of the image.

Touch

to accept the setting.

Change the background setting

If you are faxing a document that is printed on colored paper, you can enhance your fax copy quality

by removing the background that might cause your fax copy to streak or blur. Removing the

background increases resolution which also increases transmission time.

On the control panel, touch the

Fax

icon to display the Fax screen.

Scroll to and touch

More Options

Scroll to and touch

Image Adjustment

Under the

Background Cleanup

heading, touch the left arrow or touch the right arrow to change

the background setting.

Touch

to accept the setting.

20 Chapter 2 HP Color LaserJet CM3530 MFP Series

ENWW

Содержание CC487-91209









































































































































































Результаты поиска

Содержание CC487-91209

Отзывы:

HP CC487-91209, Руководство по факсу, Страница: 32 / 168

Результаты поиска

Содержание CC487-91209

Отзывы: