HP AA-RSB6B-TE Скачать руководство пользователя страница 33

Страница: 33 / 104

Installing the SAN Switch 2/8

hp StorageWorks SAN Switch 2/8 Installation Guide

Installing the SAN Switch 2/8 in a 9000 Series or

Comparable EIA Rack

Read the following sections for complete installation instructions.

Obtain the following tools:

■

Fixed Rack Mount Kit (supplied with the switch)

■

A #2 Phillips screwdriver with torque capability

■

Clamps or other means to temporarily support the switch

■

Torque screwdriver

Caution:

The SAN Switch 2/8 ships with the complete set of rack mount

hardware required for installation in an EIA rack. HP recommends using the

exact screws specified for use with the switch chassis. Using screws longer than

the specified length may damage the switch.

Installing the Fixed Rail Kit

The SAN Switch 2/8 Fixed Rack Mount Kit consists of two rail assemblies. Read
the following sections for complete instructions on attaching the rails to the
switch, then installing the switch in the rack.

1. Attach the left and right front brackets to the switch chassis as follows:

Position one left front bracket (Item 1) with the flat side against right side
of switch, oriented as shown in

Figure 6

Note:

Four sets of holes are provided to allow the switch to be set back from the front of

the rack, if desired. This allows a more gradual bend in any fiber optic cables

connected to the switch.

Insert two 8-32 x 5/16 inch screws (Item 7) into one of the pairs of
vertically aligned holes in both the bracket and in the switch.

Insert one 8-32 x 5/16 inch screw (Item 7) into one of the single holes in
both the bracket and in the switch.

d. Tighten screws to a torque of 15-inch pounds.

Содержание AA-RSB6B-TE









































































































Результаты поиска

Содержание AA-RSB6B-TE

Отзывы:

Похожие инструкции для AA-RSB6B-TE

Бренды по названию

Популярные бренды

HP AA-RSB6B-TE, Руководство по установке

Результаты поиска

Содержание AA-RSB6B-TE

Отзывы:

Похожие инструкции для AA-RSB6B-TE

Бренды по названию

Популярные бренды