HP 9000 Series Скачать руководство пользователя страница 467 | Manualshive

Страница: 467 / 472

background image

Appendix C

C-13

HotSwap Disk Bay (D Class Only)

HotSwap Procedure

Follow these steps to replace a hotswap disk module.

Step 1

• Check if the LVM found the physical volume to be defective when the volume group

was activated.

• The vgchange would have printed the following message on the console:

WARNING

VGCHANGE: WARNING: COULDN'T ATTACH TO THE VOLUME GROUP PHYSICAL
VOLUME "/DEV/DSK/cXtXdX"

THE PATH OF THE PHYSICAL VOLUME REFERS TO A DEVICE THAT DOES NOT
EXIST, OR IS NOT CONFIGURED INTO THE KERNAL.

• If the status of the vgchange is unknown, you may check if this occurred by doing a

vgdisplay command:

# vgdisplay BB VG name EB

For our example:

# vgdisplay /dev/vg00

• If the disk was defective at vgchange time, the following messages will be printed one

or more times.

WARNING:

VGDISPLAY: WARNING: COULDN'T QUERY PHYSICAL VOLUME "/DEV/DSK/cXtXdX"
THE SPECIFIED PATH DOES NOT CORRESPOND TO PHYSICAL VOLUME ATTACHED

TO THE VOLUME GROUP.
VGDISPLAY: WARNING: COULDN'T QUERY ALL OF THE PHYSICAL VOLUMES.

• If you see these messages, the disk was defective at the time the volume group was

activated.

Hot swapping a disk which was defective during activation requires a different sequence
of commands. Skip to the alternative procedure,"Hot Swap Procedure for Unattached
Physical Volumes," at the end of this document.

Otherwise, your disk became defective after the vgchange and you must continue with
step 2 of this procedure.

Step 2

• Reduce any logical volumes that have mirror copies on the faulty disk so that they no

longer mirror onto that disk (note the -A n option):

# lvreduce -m 0 -A n BB LV name EB /dev/dsk/cXtXdX for 1 way mirroring

«
...
465
466
467
468
469
...
»

Содержание 9000 Series

























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 9000 Series

Бренд: Acer Страницы: 4

Aspire Z5600 Series

Бренд: Acer Страницы: 11

Бренд: Acer Страницы: 17

Бренд: Acer Страницы: 7

Бренд: IBM Страницы: 212

9228 - IntelliStation Z - Pro

Бренд: IBM Страницы: 72

9114-275 - IntelliStation POWER 275

Бренд: IBM Страницы: 102

8863 - eServer xSeries 366

Бренд: IBM Страницы: 94

Бренд: IBM Страницы: 4

Бренд: IBM Страницы: 84

Бренд: IBM Страницы: 96

Бренд: IBM Страницы: 156

Бренд: IBM Страницы: 178

Бренд: IBM Страницы: 155

Бренд: IBM Страницы: 214

Бренд: IBASE Technology Страницы: 68

Бренд: Android Страницы: 7

Бренд: Franklin Страницы: 171

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды