HP 9000 Series Скачать руководство пользователя страница 301 | Manualshive

Страница: 301 / 472

background image

Chapter 11

11- 5

SCSI Peripherals and I/O Information

SCSI Cables

The information in this section is common to all types of SCSI busses.

1. The cable length used to connect the SCSI devices plus ANY cable length internal to the device

must not exceed the appropriate limits as previously stated.

2. Minimize the SCSI bus length but do not use cables shorter than 0.5m external.

3. Because cable impedance and construction affect bus signal quality, only HP cables are

recommended.

4. While the high-density SCSI connectors on the HP-PB Host Adapters support both thumbscrew

and squeeze latch cables, only the thumbscrew type are recommended because of reliability and
RFI concerns with the squeeze-latch cables.

Cable Characteristics

Single-Ended and Differential, 50 and 68 conductor flat cables or 25 and 34 single twisted pair cables
with a characteristic impedance of 90 to 140 ohms must be used for our application. (All Hewlett
Packard supplied cables meet this requirement.)

Voltages/Current

Single-Ended. Output Characteristics - Either open collector or tristate drivers.

Signal True (low) = 0.0 to 0.5 Vdc.

Signal False (high) = 2.25 to 5.25 Vdc.

Input Characteristics - Device powered on including drivers and passive receivers.

Signal True (low) = 0.0 to 0.8 Vdc.

Current = -0.4 to 0.0 mA @ 0.5 Vdc.

Signal False (high) = 2.0 to 5.25 Vdc.

Current = 0.0 to 0.1 mA @ 2.7 Vdc.

Differential. Output Characteristics:

V ol (Low-Level output voltage) = 1.7V max. at I ol (Low-Level output current) = 55 mA.

V oh (High-Level output voltage) = 2.7V min. at I hl (High-Level output current) = -55 mA.

V od (Differential output voltage) = 1.0V min. with common mode voltage ranges from -7 to +12
Vdc.

Input Characteristics:

I i (Input Current on either input) = +/- 2.0 mA. with input voltages between -7 and +12 Vdc. with
power on or off an with hysteresis = 35 mV min.

«
...
299
300
301
302
303
...
»

Содержание 9000 Series

























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 9000 Series

Бренд: Acer Страницы: 4

Aspire Z5600 Series

Бренд: Acer Страницы: 11

Бренд: Acer Страницы: 17

Бренд: Acer Страницы: 7

Бренд: Acer Страницы: 25

HC10 - BladeCenter - 7996

Бренд: IBM Страницы: 114

Бренд: Wincomm Страницы: 58

Бренд: Omnitronic Страницы: 56

Optiplex 9010 All In One

Бренд: Dell Страницы: 67

Бренд: Pioneer Страницы: 124

Бренд: Sonnet Страницы: 12

Бренд: Corsair Страницы: 16

32 Unit Management Cart

Бренд: Ergotron Страницы: 12

Бренд: Shuttle Страницы: 65

Бренд: IEI Technology Страницы: 151

NANO-BT-i1 Series

Бренд: IEI Technology Страницы: 153

Бренд: Icy Box Страницы: 12

Kontron SBOX-5210

Бренд: S&T Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды