HP 9000 Series Скачать руководство пользователя страница 304 | Manualshive

Страница: 304 / 472

background image

11-8

Chapter 11

SCSI Peripherals and I/O Information

Termination/Term Power

1. The SCSI bus requires termination at both ends of the bus. The host adapters generally supply on

board terminators and should be located at one end of the bus. The multifunction I/O host bus
adapters are the current exception since they are designed to reside in the middle of the SCSI bus.
Therefore, buses associated to these multifunction I/O adapters are terminated on the two ends of
the associated internal and external buses. Since an external connection may not be present, insure
that the ACTIVE terminators supplied with the product are installed on the external connection at
the back of the system.

2. When possible, put devices that supply termination power at both ends of the bus. The host

adapters will always supply termination power which is required for proper bus operation.
However, noise immunity can be improved by placing another source of termination power at the
other end of the bus. Most peripheral devices are optionally capable of supply termination power.
(See the appropriate peripheral descriptions in this section.)

Termination Characteristics and Power

Terminator power - Will be supplied by the Initiators and may be supplied by any or all connected
devices. HP recommends that terminator power be supplied by the Host Bus Adapter (HBA) Initiator
and the last device on the SCSI Bus to help decrease interface error rates and provide better balance to
the TERMPWR contacts. Recommended current limiting is 1.5 amps. with a maximum of 5 amps.
(The limiting device may be fused or resetable.)

Single-Ended

TERMPWR = 4.25 to 5.25 vdc. with 900 ma source drive capability for the 50-pin Cable, and 1500
ma source drive capability for the 68-pin cable.

+MSG

25

49

50

59

-MSG

+SEL

26

51

52

60

-SEL

+C/D

27

53

54

61

-C/D

+REQ

28

55

56

62

-REQ

+I/O

29

57

58

63

-I/O

Ground

30

59

60

64

Ground

+DB(8)

31

61

62

65

-DB(8)

+DB(9)

32

63

64

66

-DB(9)

+DB(10)

33

65

66

67

-DB(10)

+DB(11)

34

67

68

68

-DB(11)

Signal Name

Connector

Contact

Number

Cable

Conductor

Number

Cable

Conductor

Number

Connector

Contact

Number

Signal Name

«
...
302
303
304
305
306
...
»

Содержание 9000 Series

























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 9000 Series

Бренд: PROAIM Страницы: 3

TRS-80 Model 100

Бренд: Radio Shack Страницы: 210

Бренд: PRESONUS Страницы: 8

Бренд: Digital Equipment Страницы: 96

Бренд: Moxa Technologies Страницы: 2

MARINE COMPUTER - INSTALLATION REV A

Бренд: Simrad Страницы: 40

Бренд: Büttner Elektronik Страницы: 36

PCV-J200 - Vaio Desktop Computer

Бренд: Sony Страницы: 1

PCV-J120 - Vaio Desktop Computer

Бренд: Sony Страницы: 1

PCV-J100 - Vaio Desktop Computer

Бренд: Sony Страницы: 1

PCV-J120 - Vaio Desktop Computer

Бренд: Sony Страницы: 24

PCV-J200 - Vaio Desktop Computer

Бренд: Sony Страницы: 29

PCV-J150 - Vaio Desktop Computer

Бренд: Sony Страницы: 27

PCV-L400 - Vaio Slimtop Computer

Бренд: Sony Страницы: 35

PCV-E314DS - Vaio Digital Studio Desktop Computer

Бренд: Sony Страницы: 33

Бренд: Sony Страницы: 63

PCV-L620 - Vaio Slimtop Computer

Бренд: Sony Страницы: 104

PCV-J200 - Vaio Desktop Computer

Бренд: Sony Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды