HP 8719ES Скачать руководство пользователя страница 46

Страница: 46 / 52

14-32

Service Guide

Assembly Replacement and Post-Repair Procedures

HP 8719ET/20ET/22ET

Removing the A26 High Stability Frequency Reference (Option 1D5) Assembly

HP 8719ES/20ES/22ES

RF Network Analyzers

Removing the A26 High Stability Frequency Reference
(Option 1D5) Assembly

Tools Required

• T-10 TORX screwdriver

• T-15 TORX screwdriver

• 9/16-inch hex-nut driver

• ESD (electrostatic discharge) grounding wrist strap

Removal

1. Remove the rear panel, refer to

“Removing the Rear Panel Assembly” on page 14-14

2. Disconnect W30 from the high stability frequency reference board (A26).

3. Remove the BNC connector nut and washer from the "10 MHz PRECISION

REFERENCE" connector (item 1) on the rear panel.

4. Remove the screw (item 4) that attaches the 1D5 assembly to the rear panel.

5. Remove the screw (item 2) that secures the high stability frequency reference board

(A26) to the bracket.

6. Slide the board out of the bracket. Be careful not to lose the plastic spacer washer

(item 3) that is on the BNC connector as the board is being removed.

Replacement

1. Reverse the order of the removal procedure.

NOTE

Before reinserting the high stability frequency reference board (A26) into the
bracket, be sure the plastic spacer washer (item 3) is on the BNC connector.

Содержание 8719ES




















































Результаты поиска

Содержание 8719ES

Отзывы:

Похожие инструкции для 8719ES

Бренды по названию

Популярные бренды

HP 8719ES, Руководство по обслуживанию

Результаты поиска

Содержание 8719ES

Отзывы:

Похожие инструкции для 8719ES

Бренды по названию

Популярные бренды