manualshive.com logo in svg

HP 8719ES, Руководство по обслуживанию

Поделиться
Скачать
HP 8719ES Скачать руководство пользователя страница 22

14-8

Service Guide

Assembly Replacement and Post-Repair Procedures

HP 8719ET/20ET/22ET

Removing the Front Panel Assembly

HP 8719ES/20ES/22ES

RF Network Analyzers

Removing the Front Panel Assembly

Tools Required

• T-10 TORX screwdriver

• T-15 TORX screwdriver

• small slot screwdriver

• ESD (electrostatic discharge) grounding wrist strap

• 5/16-inch open-end torque wrench (set to 10 in-lb)

Removal

1. Disconnect the power cord.

2. Remove the front bottom feet (item 1).

3. Remove all the RF cables that are attached to the front panel (item 2).

NOTE

Options may differ from figure and have more than one RF cable on the front
panel.

4. Remove the Line button (item 3).

5. Remove the trim strips (item 4) from the top edge of the front frame by prying under the

strip with a small slot screwdriver.

6. Remove the 7 screws (item 5) from the top and bottom edges of the frame.

a. Remove all 4 flathead screws from the top and the 3 flathead screws from the

bottom.

NOTE

The 3 bottom screws are on both ends and in the middle. They look like the
screws from the top. Do not remove the other 6 screws from the bottom.

7. Slide the front panel over the test port connectors.

8. Disconnect the ribbon cables (item 6) and (item 7). The front panel is now free from the

instrument.

Replacement

1. Reverse the order of the removal procedure.

NOTE

When reconnecting semirigid cables, torque the to 10 in-lb.

Содержание 8719ES





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды