HP 333A Скачать руководство пользователя страница 37

Страница: 37 / 53

TM 11-6625-1576-15

Section V

Paragraph 5-43 to 5-45

The -hp- Part Number for the assembly is marked on
the circuit board to identify it.

5-43. The etched circuit boards are of the plated-

through type.

The electrical connection between the

two sides of the board is made by a layer of metal
plated through the component hole. When working on
these boards, observe the following rides:

a. Use a low-heat (25 to 30 watts) small-tip sol-

dering iron, and a small diameter rosin core solder.

b. Remove circuit components by placing the sol-

dering iron on the component lead on either side of the
board, and pulling up on the lead. If a component is
obviously damaged, clip leads off as close to the com-
ponent as possible and then remove leads with a sol-
dering iron.

EXCESSIVE HEAT CAN CAUSE THE CIR-
CUIT AND BOARD TO SEPARATE, OR
CAUSE DAMAGE TO THE COMPONENTS.

c. Clean component lead hole by heating the hole

with the iron and inserting a wooden toothpick Re-
move the toothpick after the solder has cooled and

insert the new component lead

d. To replace components, shape new leads and

insert them in lead holes. Reheat with soldering iron
and add a small amount of new solder as required to
insure a good electrical connection.

e. Clean excessive flux from the connection and

adjoining area

5-44. SERVICING ROTARY SWITCHES.

5-45. The 333A/334A has five rotary type switches
FUNCTION, SENSITIVITY, FREQUENCY RANGE,

MODE, and METER RANGE. When working on these

switches, observe the following rules:

a. Use a low-heat (25 to 50 watts) small-tip sol-

dering iron and a small diameter rosin core solder.

b. When replacing components, attempt to dress

them as nearly to their original alignment as possible.

c. Clean excessive flux from the connection and

adjoining area.

d. After cleaning the switch, apply a light coat of

lubriplate to the switch detent balls. DO NOT apply
lubricant to the switch contacts or allow lubricant to
contaminate components.

5-13

Содержание 333A






















































Результаты поиска

Содержание 333A

Отзывы:

Похожие инструкции для 333A

Бренды по названию

Популярные бренды

HP 333A, Техническое руководство

Результаты поиска

Содержание 333A

Отзывы:

Похожие инструкции для 333A

Бренды по названию

Популярные бренды