Hozelock Cyprio EASYCLEAR 3000LV, Руководство пользователя, Страница: 6 / 68

• The pump is supplied with 3m of 2 core electric
cable which is permanently connected and sealed
to the pump.
The supply cable cannot be
replaced. If the cable is damaged, the unit
should be discarded.
The plug supplied with this
product is not waterproof and must be housed in
a dry, waterproof enclosure.
• The installation must conform to the national
and local wiring regulations which could include
the use of plastic or metal conduit to protect the
cable.
• Ensure 230v cable and 24v cables do not cross.
• The unit cable should be positioned and
adequately protected against damage especially
where contact with gardening equipment (lawn
mowers, forks etc.) children and domestic
animals may occur.
Connect the pump to the transformer as follows
(See fig-11):
A - Mains voltage cable.
B - Flying Lead.
C - Low voltage cable to pump.
Screw the transformer into position ensuring
easy access to the terminal block. Plug the pump
lead into the socket provided on the flying lead
for the transformer. If an extension lead is
required Hozelock Cyprio can provide this (refer
to Hozelock Cyprio Consumer Services).
Also see General Safety & Guidelines section for
further information.
Position - Construct a solid and level platform on
which to place the EasyClear™. The platform
should be greater than 300 mm (12") below the
water level. For depths between 300mm and
600mm use the fountain stem extension
segments (Fig 1-F), which simply screw together,
to allow the fountain to be above the water
level. For general installation see Fig 4 A/B.
When using the EasyClear for a waterfall the
entire unit should be submersed.
Connection - Place the unit next to the pond and
route the cable back to the mains supply. Ensure
that you allow for enough cable for positioning
the product in the desired location in the pond
and prevent the connector from entering the
water.
Bell Fountain (Fig 1).
Locate the Bell Support (B) to the Bell Main Body
(C) and push fully home. Position the Bell (D) to
the Body Assembly and press into the central
location
.
2 and 3 tier fountain display assembly (Fig 1-E).
The plastic discs that create the 2 and 3 tier
water displays simply snap onto the fountain
stem. Push the fountain stem into the fountain
stem extension segment (Fig 1-F) and screw onto
the fountain outlet (Fig 1-A).
(Fig 4-A for general installation guide)
Please note: The product has a water by-pass to
control water flow rates which means a quantity
of water will always come out of the product
just below the flow control. This is normal in
operation.
Position the unit in the pond. The fountain angle
can be adjusted to be vertical using the ball joint
(Fig 2-A). The tightness of the ball joint can be
adjusted (Fig 2-J)
If required, the 2-Tier Fountainhead can be used
to achieve an alternative and higher display
pattern than the 3-Tier.
The fountain height can be adjusted to suit your
needs by rotating the Fountain Flow Adjuster.
(Fig 3-K)
The Bell Fountain creates a decorative waterbell.
The size of the bell can be adjusted to suit your
needs by rotating the Fountain Flow Adjuster
(Fig 3-K).
(Fig 4-B for general installation guide)
Position the pump as previously described.
Attach a suitable length (3m maximum) of 25
mm (1”) hose to the waterfall hose tail (Fig 1-G)
and secure with a suitable hose clip and position
the outlet end of the hose in the desired
position.
Screw the waterfall hose tail to the fountain
outlet of the EasyClear™ (Fig 1-A) and adjust the
flow using the fountain flow adjuster, (Fig 3-K),
to suit your needs.
Waterfall Only Operation
Fountain Only Operation
Accessory Assembly
EasyClear Installation
Transformer Installation
33707 EASY CLEAR 3000LV UI's(29-8-8) 16/9/08 10:09 Page 6