Hoval TopGas classic 100 Скачать руководство пользователя страница 6

6

4 219 316 / 00

IMPORTanT nOTES

1.7 

Regulations, standards, ordinances to be 

complied with for proper use

The locally applicable heating system regulations must 

be followed when planning, installing and operating the 

gas heat generator:

•  The regulations of the local building authorities, insur-

ance companies, chimney sweeps and the state/can-

ton. etc. must also be taken into account.

•  The regulations of the responsible gas supply company 

are to be complied with if using gas.

•  Regulations governing the discharge and treatment of 

condensate are subject to the specifications of the local 

water authorities.

•  Approval by the authorities may be required for instal-

lation.

The standards, guidelines and ordinances listed for the 

specific countries are relevant for the installation and op

-

eration of the gas heat generator. The list is intended as 

an aid. It is not complete. The currently applicable regula-

tions must be observed.

Germany §

•  DIN EN 12828 Heating systems in buildings - Design 

of hot water heating systems

• 

DIN EN 12831 Energy efficiency of buildings - Method 

for calculation of the design heat load

•  DIN EN 13384 Flue gas systems – Calculation meth-

ods in heat and flow engineering

•  DIN EN 14868: Protection of metallic materials against 

corrosion - Guidance on the assessment of corrosion 

likelihood in closed water circulation systems

•  DIN EN 50156; VDE 0116: Electrical equipment of 

combustion plants and associated facilities

•  DIN VDE 0100 Erection of low-voltage installations 

(for electrical installation and the TAB (technical con-

nection requirements of the relevant energy supply 

company))

•  VDI 2035 Prevention of damage in hot water / heating 

systems by corrosion and the formation of scale in 

closed hot water heating systems.

•  Rules for gas established by DVGW (in particular 

DVGW-TRGI Technical rules for gas installations)

•  Firing ordinance of the federal states

• 

Technical specifications of the gas supply companies

•  Worksheet DWA-A 251 Condensate from condensing 

boilers

The regulations of the local water authorities could 

deviate from the rules in this worksheet.

•  Accident prevention regulations

 - DGUV Regulation 1 Accident prevention regulations 

- Guidelines for prevention

 - DGUV Regulation 4 Accident prevention regulations 

- Electrical installations and equipment

Austria §

• 

ÖNORM EN 12828 Heating systems in buildings - De

-

sign of hot water heating systems

• 

ÖNORM EN 12831 Energy efficiency of buildings - 

Method for calculation of the design heat load

• 

ÖNORM EN 13384 Flue gas systems - Heat and flow 

calculation methods

• 

ÖNORM EN 14868: Protection of metallic materials 

against corrosion - Guidance on the assessment of 

corrosion likelihood in closed water circulation systems

•  OVE 50156: Electrical equipment of combustion plants 

and associated facilities

• 

ÖNORM H 5152 Calorific plants - Planning guidelines

• 

ÖNORM H 5170 Heating systems - Requirements 

with respect to building and safety technology, fire and 

environmental protection

• 

ÖNORM H 5195-1 Heat transfer fluid for building tech

-

nology - Prevention of damage by corrosion and the 

formation of scale in closed hot water heating systems

•  ÖVGW rules for gas

• 

Technical specifications of the gas supply companies

•  SNT regulations

Switzerland §

•  SN EN 12828+A1;SIA 384.101+A1 Heating systems in 

buildings - Design of hot water heating systems

• 

SN DIN EN 12831 Energy efficiency of buildings - 

Method for calculation of the design heat load

•  SN EN 13384;SIA 384.42x Flue gas systems - Heat 

and flow calculation methods

•  SN EN 14868: Protection of metallic materials against 

corrosion - Guidance on the assessment of corrosion 

likelihood in closed water circulation systems

•  SN EN 50156: Electrical equipment of combustion 

plants and associated facilities

• 

SWKI 91-1 Aeration and ventilation of the boiler room

• 

SWKI 93-1 Safety engineering installations for heating 

systems

•  SWKI BT102-01 Water quality for building services 

systems

•  SVGW rules for gas

• 

Swiss fire protection regulations (BSV) of the VKF 

(Association of Cantonal Fire Insurers)

• 

Regulations of the cantonal and local fire authorities

•  Water Protection Regulation (GSchV)

• 

EKAS - Guidelines for liquefied gas

Other countries §

For all other countries of destination, the locally applicable 

country-specific regulations must be observed.

Содержание TopGas classic 100

















































Отзывы: