Hoval STU 200 Скачать руководство пользователя страница 9

Страница: 9 / 56

Hoval STU Wood Pellet Boiler

Dimensions and Technical Information

Key:
1

Flow

Returns, one either side, both

to be connected to a common

inlet header

Safety valve connection

Drain connections (plugged)

Stat & modulating sensor

mounting sockets

Combustion chamber pressure

switch connection

Smoke box condensate drain

Cooling coils c/w temp sensor

Temperature gauge

Smoke box cleaning doors

Sight glass assembly

Twin delivery augers

Burn back Stat (one per stoker)

Burn back water dump (one per

stoker)

Temp. sensor for water dump

device (one per stoker)

Boiler door Microswitch

Common transfer box with two

No. proximity sensors

Motorised burnback protection

damper

Combustion Chamber Pressure

switch

Notes:

• Thermal safety heat exchanger connections c/w thermostatic

control valve connection (3/4") to be connected to a cold water

mains supply. Drain pipework (by others) to be run via tundish

to drain. See Appendix B, for further details.

• Boiler mounted control panel not shown but the typical size for

models 800 and 1000: 800mm W x 1200mm H x 300mm D

This may change and should be checked on a site by site basis.

Connections:

800

1000

1 Flow

(PN6)

DN125

DN150

2 Return

(PN6) 2xDN125 2xDN150

3 Safety valve

(BSP)

4 Drain

(BSP) 2xG1.1/2 2xG1.1/2

5 Stat pockets

(BSP) 2xG1/2"

2xG1/2"

6 Pressure switch (BSP)

R3/4"

7 Smoke box drain (mm)

G3/4"

8 Cooling Coils

(mm)

G3/4"

STU Boiler

800

1000

(mm)

3134

3282

(mm)

1540

(mm)

2530

2713

(mm)

2962

3110

(mm)

710

723

(mm)

1195

1150

(mm)

1060

(mm)

285

(mm)

441

(mm)

200

(mm)

1284

1299

A 3ph + N 32A 400V supply is

required for the control panel

operation.

An automatic air vent, should be fitted by

the installer at high level on the flow

pipework connecting to the boiler.

Содержание STU 200

























































Результаты поиска

Содержание STU 200

Отзывы:

Похожие инструкции для STU 200

Бренды по названию

Популярные бренды

Hoval STU 200, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание STU 200

Отзывы:

Похожие инструкции для STU 200

Бренды по названию

Популярные бренды