background image

 

Replacement parts must comply with the technical requirements of the system 

manufacturer. Hoval recommends the use of original spare parts.

 

Unauthorised reconfiguration or modification of the unit is not permitted.

 

Shut down the unit immediately, if any defects are ascertained that limit the 

operational safety.

2.3  Decommissioning

 

Switch off heating operation (operating mode 'L_OFF').

 

Close the cut-off valve in the gas supply line.

 

Let the unit cool off. The heating pump continues to run to cool down the heat 

exchanger.

 Attention

Fire hazard due to hot components. Do not switch off the power supply 

until the heating pump comes to a complete stop!

 

When the heating pump comes to a stop: Turn the isolation switch on the unit to 

the 'Off' position.

2.4  Emergency situations

In emergency situations:

 

Disconnect the power supply with the main switch in the control panel. The unit 

stops immediately. In this case, the orderly cool down of the heat exchanger 

does not happen.

 

Close the cut-off valve in the gas supply line.

2.5  Regulations

Observe all applicable national regulations and standards as well as generally 

accepted engineering practice for the installation and operation of gas-fired units.

4

5

RoofVent

®

 KG

Operating instructions

Safety

Safety

4 220 755-en-00

Содержание RoofVent KG









































Отзывы: