Hottek 125647 Скачать руководство пользователя страница 12

ENG

12

Blade Oiling

• 

To maintain your hair clipper in peak condition, the blades should be oiled 

using the engine oil.

• 

Do not use hair oil, grease, oil mixed with kerosene or any solvent. 

• 

The solvent will evaporate and leave a thick oil which may slow down the 

blades motion.

Blade Lever (5)

• 

The blade lever (5) is conveniently located near your thumb (if you’re right-

handed) so it can be easily adjusted while the clipper is in your hand.

•  The blade lever adds versatility to your clipper by allowing you to gradually 

change the closeness of your cut without an attachment comb.

• 

When the blade lever is in the uppermost position, the blades will give you 

the closest cut and leave the hair very short. Pushing the lever downward 

gradually increases the cutting length.

• 

In its lowest position, the blade lever will leave the hair approximately the 

same length as 6.1 attachment comb (3mm). 

• 

In its highest position, the blade lever will leave the hair approximately the 

same length as 6.4 attachment comb (12mm).

• 

The blade lever (5) will also extend the use of your blades since a different 

cutting edge is used in each setting. 

• 

The blade lever (5) will help to remove hair that has stuck between the blades. 

• 

To remove stuck hair, move the blade lever (5) from lower to upper position 

a couple of times.

• 

If your hair clipper stops cutting and this does not help, your cutting blades 

are dulled. Replace them with new blades.

Warning:

 Clean the blades from hair when idle and after each haircut. This will 

remove any and all remaining hair.

Before First Use

• 

Before each use inspect the hair clipper and ensure that it is free from oil 

between the cutting blade teeth. 

• 

Switch the hair clipper on to distribute the oil and to make sure it is running smoothly.

• 

While using the appliance, untwist the cord from time to time to avoid tangling.

• 

Seat a person so that his/her head is at your eyes level. This provides better 

control of hair cutting. 

• 

Before cutting always carefully comb hair to ensure that there are no tangles. 

• 

Place a towel around the neck of a person having the haircut to avoid the 

cut hair to fall under the collar. 

Содержание 125647

























Отзывы: