2
FIRST TIME USE
SALT, RINSE AID AND DETERGENT
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the reta-
ining elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and
on the machine’s functional components.
• It is important that the salt reservoir be never empty.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher
(see PRODUCT DESCRIPTION)
and should be fi lled when the
SALT REFILL
indicator light
in the control panel is lit.
1. Remove the lower rack and unscrew the
reservoir cap (anticlockwise).
2. Only the fi rst time you do this: fi ll the salt re-
servoir with water.
3. Position the funnel
(see fi gure)
and fi ll the salt
reservoir right up to its edge (approximately
1 kg); it is not unusual for a little water to leak
out.
4. Remove the funnel and wipe any salt residue
away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
Whenever you need to add salt, we recommend carrying out the
procedure before the washing cycle is started.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in
your house. This information can be obtained from your local water
supplier.
The factory setting is for average (3) water hardness.
• Switch on the appliance by pressing the
ON/OFF
button.
• Switch
off the appliance by pressing the
ON/OFF
button.
• Hold down button
START/Pause
for 5 seconds, until you hear a
beep.
• Switch on the appliance by pressing the
ON/OFF
button.
• The
ON/OFF
LED
light will fl ash as many times as the level that was set.
• Set the desired water hardness level using the
PROGRAM SELECTION
knob
(
see WATER HARDNESS TABLE
).
• Switch
off the appliance by pressing the
ON/OFF
button.
Setting is complete!
As soon as this procedure is complete, run a program without loading.
Only use salt that has been specifi cally designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indi-
cator light switches off .
If the salt container is not fi lled, the water softener and the
heating element may be damaged as a result.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser
A
should
be fi lled when the
RINSE AID REFILL
indicator light in the control
panel is lit.
1. Open the dispenser
B
by pressing and pulling up the tab on the lid.
2. Pour in the rinse aid (max.110 ml), making sure it does not overfl ow
from the dispenser. If this happens, clean the spill immediately with
a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfi ed with the drying results, you can ad-
just the quantity of rinse aid used.
• Switch the dishwasher on using the
ON/OFF
button.
• Switch it off using the
ON/OFF
button.
• Press
button
START/Pause
three times - a beep will be heard.
• Switch it on using the
ON/OFF
button.
• The
START LED
light will fl ash as many times as the level that was set.
• Set the level of rinse aid quantity to be supplied using the
PROGRAM
SELECTION knob
(see PROGRAMS TABLE)
.
• Switch it off using the
ON/OFF
button
Setting is complete!
If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied. The
LOW RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 5 levels can be set according to the dishwasher model.
The factory setting is specifi c to the model, please follow instruction
above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes, set a
mid-range number (4-5).
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device A.
Introduce the detergent into the dry dispenser B only. Place the
amount of detergent for pre-washing directly inside the tub.
1. When measuring out the detergent
refer to the mentioned earlier infor-
mation to add the proper quantity.
Inside the dispenser
B
there are
indications to help the detergent
dosing.
2. Remove detergent residues from
the edges of the dispenser and clo-
se the cover until it clicks.
3. Close the lid of the detergent di-
spenser by pulling it up until the
closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program.
If all-in-one detergents are used, we recommend using the
TABLET
button, because it adjusts the program so that the best washing and
drying results are always achieved.
A
B
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
1
Soft
0 - 6
0 - 10
2
Medium
7 - 11
11 - 20
3
Average
12 - 17
21 - 30
4
Hard
17 - 34
31 - 60
5
Very hard
35 - 50
61 - 90
A
B
