Downloaded from www.vandenborre.be
Downloaded from www.vandenborre.be
1
5
C
onne
c
t
in
g
a
f
l
e
x
i
b
l
e
j
oin
t
l
ess
s
t
ain
l
ess
s
t
ee
l
p
i
p
e
t
o
a
t
h
rea
d
e
d
a
tt
a
chm
en
t
The gas supply pipe fitting is a threaded 1/2 gas cylindrical
male attachment.
These pipes must be installed so that they are never longer
than 2000 mm when fully extended. Once connection has
been carried out, make sure that the flexible metal pipe
does not touch any moving parts and is not compressed.
Only use pipes and seals that comply with current national
regulations.
C
h
e
c
k
in
g
t
h
e
t
i
gh
t
ness
o
f
t
h
e
c
onne
c
t
ion
When the installation process is complete, check the pipe
fittings for leaks using a soapy solution. Never use a flame.
A
d
a
p
t
in
g
t
o
d
i
ff
eren
t
t
y
p
es
o
f
g
as
To adapt the hob to a different type of gas other than default
type (indicated on the rating plate at the base of the hob or
on the packaging), the burner nozzles should be replaced
as follows:
1. Remove the hob grids and slide the burners off their
seats.
2. Unscrew the nozzles using a 7 mm socket spanner, and
replace them with nozzles for the new type of gas (see
table 1
B
urner and nozzle characteristics).
3. Reassemble the parts following the above procedure in
the reverse order.
4. Once this procedure is finished, replace the old rating
sticker with one indicating the new type of gas used.
Sticker are available from any of our Service Centres.
Adjusting the burners primary air :
Does not require adjusting.
Setting the burners to minimum:
1. Turn the tap to the low flame position.
the adjustment screw, which is
positioned in or next to the tap pin,
until the flame is small but steady.
3.
H
aving adjusted the flame to the required low setting,
while the burner is alight, quickly change the position of
the knob from minimum to maximum and vice versa
several times, checking that the flame does not go out.
4. Some appliances have a safety device (thermocouple)
fitted. If the device fails to work when the burners are set
to the low flame setting, increase this low flame setting
using the adjusting screw.
5. Once the adjustment has been made, replace the seals
on the by-passes using sealing wax or a similar
substance.
If the appliance is connected to liquid gas, the regulation
screw must be fastened as tightly as possible.
Once this procedure is finished, replace the old rating
sticker with one indicating the new type of gas used.
Stickers are available from any of our Service Centres.
Should the gas pressure used be different (or vary slightly)
from the recommended pressure, a suitable pressure
regulator must be fitted to the inlet pipe (in order to comply
with current national regulations).
D
ATA
PL
ATE
E
lectrical
connections
220-240V
~
50/60H
z
This
appliance
conforms
to
the
following
European
Economic
Community
directives:
-2006/95/EEC
dated
12/12/06
(Low
Voltage)
and
subsequent
amendments
-
89/336/EEC
dated
03/05/89
(Electromagnetic
Compatibility)
and
subsequent
amendments
-
93/68/EEC
dated
22/07/93
and
subsequent
amendments.
-
90/336/EEC
dated
29/06/90
(Gas)
and
subsequent
amendments.
-
2002/96/EC