background image

8

PROGRAMMES

COOLTUMBLE PHASE 

This is the programmes final phase. Approximately 10  minutes before the finish, th eknob advances 
automatically to the Cool Tumble Phase. Heating elements turn themselves off and clothing is cooled 
down, after this the buzzer will sound (if selected) and the clothing ready to be taken out.
Always allow the dryer to complete this phase.

EASY IRON PROGRAMME 

Easy Iron is a short 10 minute programme (8 minutes of heat, followed by a 2 minute cool tumble 
period) which fluffs the fibres of clothing that have been left in the same position/location for an 
extended period of time. The cycle relaxes the fibres and makes them easier to iron and fold.

NOTE: -

 Easy Iron is 

not a drying programme

 and should not be used for wet articles of clothing.

For best results: -
1.

Do not load more than the maximum capacity. These numbers refer to dry weight.

Fabric

Maximum Load

Cotton and Cotton mixtures 2.5 kg
Synthetics

2 kg

Denim

2 kg

2.

Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and 
put them away in the closet. Should this not be possible, repeat the programme.

The Easy Iron effect varies from one fabric to the next. It works well on traditional fabrics like Cotton 
or Cotton mix and less well on acrylic fabrics and on materials such as Tencel®.

Programme

What it does...

How to set it...

Note:

Automatic
Drying

(average loads)

Dries completely: 
your clothes are ready to be
worn. 
For average loads (from 1 to
3kg) of Cotton      , polycotton 
or synthetics       .

!

If you select LOW HEAT,

this programme will not dry
your clothes. For Acrylic
fibres or small loads select
Timed Drying.

This programme can also be
used for large loads if you
require a slightly drier result.

1. Select HIGH HEAT       

by pressing the HEAT button.

2. Position the PROGRAMMES knob 

on

.

3. Press the START button     , the

ACTIVE light        will turn on.

Automatic
Drying

(large loads)

Dries completely: 
your clothes are ready to be
worn. 
For large loads (from 3 to 6kg) of
Cotton      .

!

If you select LOW HEAT,

this programme will not dry
your clothes. For Acrylic
fibres or small loads select
Timed Drying.

This programme can also be
used for average loads if you
prefer a damper result.

Timed Drying

up to 120 minutes

Dries wet clothes that will be
ironed, Acrylic fibres       , or small
loads (less than 1kg).
If you prefer a timed programme
can be used for other fabrics on
HIGH or LOW heat as appropriate
(

see Laundry

).

Consult suggested drying
times (

see Laundry

).

!

This is not a drying 

programme (

see below

).

1. Position the PROGRAMMES knob

on       .

2. Press the START button     , the

ACTIVE light       will turn on.

Use to refresh fibres of clothing
(approximately 10 minutes).

1. Select required heat setting HIGH

HEAT           or LOW HEAT      by 
pressing the HEAT button.

2. Position the PROGRAMMES knob

on the desired time.

3. Press the START button    , the

ACTIVE light        will turn on.

Easy Iron

Cool Tumble

Brief programme (approximately
10 minutes) that softens fibres of
clothing that is ready for ironing.

!

This is not a drying 

programme (

see below

).

1. Select HIGH HEAT      

by pressing the HEAT button.

2. Position the PROGRAMMES knob 

on        .

3. Press the START button     , the

ACTIVE light        will turn on.

1. Select HIGH HEAT      

by pressing the HEAT button.

2. Position the PROGRAMMES knob

on         .

3. Press the START button    , the

ACTIVE light       will turn on.

Содержание AS600VEX
























Отзывы: