Hotenda MPC8349EA Скачать руководство пользователя страница 30

Страница: 30 / 87

Electronic Component Distributor. Source::Freescale Semiconductor

P.N:MPC8349CZUAGDB Desc:IC MPU POWERQUICC II PRO 672TBGA
Web:http://www.hotenda.cn E-mail:[email protected] Phone:(+86) 075583794354

MPC8349EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 13

Freescale Semiconductor

Ethernet: Three-Speed Ethernet, MII Management

8.2.4

RGMII and RTBI AC Timing

Specifications

Table 31

presents the RGMII and RTBI AC timing specifications.

Table 31. RGMII and RTBI AC Timing Specifications

At recommended operating conditions with LV

of 2.5 V ± 5%.

Parameter/Condition

Symbol

Min

Typ

Max

Unit

Data to clock output skew (at transmitter)

SKRGT

–0.5

—

0.5

Data to clock input skew (at receiver)

SKRGT

1.0

—

2.8

Clock cycle duration

RGT

7.2

8.0

8.8

Duty cycle for 1000Base-T

4, 5

RGTH

RGT

Duty cycle for 10BASE-T and 100BASE-TX

3, 5

RGTH

RGT

Rise time (20%–80%)

RGTR

—

0.75

Fall time (80%–20%)

RGTF

—

0.75

Notes:

1. In general, the clock reference symbol for this section is based on the symbols RGT to represent RGMII and RTBI timing. For

example, the subscript of t

RGT

represents the TBI (T) receive (RX) clock. Also, the notation for rise (R) and fall (F) times

follows the clock symbol. For symbols representing skews, the subscript is SK followed by the clock being skewed (RGT).

2. This implies that PC board design requires clocks to be routed so that an additional trace delay of greater than 1.5 ns is added

to the associated clock signal.

3. For 10 and 100 Mbps, t

RGT

scales to 400 ns ± 40 ns and 40 ns ± 4 ns, respectively.

4. Duty cycle may be stretched/shrunk during speed changes or while transitioning to a received packet clock domains as long

as the minimum duty cycle is not violated and stretching occurs for no more than three t

RGT

of the lowest speed transitioned.

5. Duty cycle reference is LV

/2.

30 / 87

Содержание MPC8349EA
























































































Результаты поиска

Содержание MPC8349EA

Отзывы:

Похожие инструкции для MPC8349EA

Бренды по названию

Популярные бренды

Hotenda MPC8349EA, Технические данные инструкция

Результаты поиска

Содержание MPC8349EA

Отзывы:

Похожие инструкции для MPC8349EA

Бренды по названию

Популярные бренды