Hoshizaki SRK-14H Скачать руководство пользователя | Manualshive

Страница: 2 / 29

background image

IMPORTANT

Only qualified service technicians should attempt to install, service, or maintain
this icemaker. No installation, service, or maintenance should be undertaken
until the technician has thoroughly read this Instruction Manual. Likewise, the
owner/manager should not proceed to operate the icemaker until the installer
has instructed them on its proper operation. Failure to install, operate, and
maintain the equipment in accordance with this manual may adversely affect
safety, performance, and warranty coverage.

HOSHIZAKI provides this manual primarily to assist qualified service technicians in the
installation, maintenance, and service of the icemaker.

Should the reader have any questions or concerns which have not been satisfactorily
addressed, please call, write, or send an e-mail message to the HOSHIZAKI Technical
Support Department for assistance.

HOSHIZAKI AMERICA, INC.
618 Highway 74 South
Peachtree City, GA 30269

Attn: HOSHIZAKI Technical Support Department

Phone: 1-800-233-1940 Technical Service

(770) 487-2331

Fax: 1-800-843-1056

(770) 487-3360

E-mail: [email protected]

Web Site: www.hoshizaki.com

NOTE:

To expedite assistance, all correspondence/communication MUST include the

following information:

    • Model Number ________________________

    • Serial Number ________________________

• Complete and detailed explanation of the problem.

«
1
2
3
4
...
»

Содержание SRK-14H






























Отзывы:

Нет отзывов

Похожие инструкции для SRK-14H

Бренд: Firesense Страницы: 16

Бренд: Versamatic Страницы: 18

Бренд: DAYLIFF Страницы: 8

Бренд: Malmbergs Страницы: 12

Бренд: Eagle Pro Страницы: 50

SL MINITHERM DNLA

Бренд: Intertec Data Systems Страницы: 8

Бренд: SFA-SANIFLO Страницы: 14

Бренд: DROPSA Страницы: 16

Warren Rupp SANDPIPER Beast SPB20

Бренд: Idex Страницы: 21

Бренд: S&P Страницы: 52

Бренд: Qlima Страницы: 64

FLOJET G57C Series

Бренд: ITT Страницы: 4

Бренд: Aurora Страницы: 5

Бренд: GRALUX Страницы: 16

Бренд: Radiant Optics Страницы: 4

Бренд: Master Страницы: 15

FlowSol B HE WMZ

Бренд: Resol Страницы: 8

$SAER Elettropompe SDLV-TEX Use And Maintenance Manual preview$

Бренд: SAER Elettropompe Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды