Hoshizaki SRK-14H Скачать руководство пользователя | Manualshive

Страница: 12 / 29

background image

1

2. Condensing Unit

• Top Panel: Remove the screws and lift off.
• Front Panel: Remove the screws and lift off.
• Left Side/Rear Panel: Remove the screws and lift off.
• Louver Panel: Remove the screws and lift off.
• Right Side Panel: Remove the screws and lift off.

C. How to Remove Panels

1. Icemaker

• Front Panel: Remove the screw. Lift up and towards you.
• Top Panel: Lift off.
• Side Panel (R): Remove the screw. Slide forward slightly and lift off.
• Insulation Panel: Remove the thumbscrews. Lift up slightly and pull towards you.

Fig. 3

Top Panel

Right Side Panel

Louver Panel

Left Side/Rear Panel

Front Panel

Condensing Unit

Side Panel (R)

Fig. 2

Top Panel

Front Panel

Insulation Panel

Icemaker

Valve Box

Access Panel

«
...
10
11
12
13
14
...
»

Содержание SRK-14H






























Отзывы:

Нет отзывов

Похожие инструкции для SRK-14H

Бренд: EAS Electric Страницы: 165

Бренд: Larzep Страницы: 14

DONYER POWER CH-1500

Бренд: Intertek Страницы: 12

Бренд: Wilo Страницы: 76

Бренд: Orbegozo Страницы: 85

Бренд: Jandy Страницы: 24

Бренд: EBARA Страницы: 28

Бренд: K&T Страницы: 17

Бренд: Olimpia splendid Страницы: 12

Бренд: EDM Product Страницы: 25

Бренд: KABI Страницы: 6

Бренд: salmson Страницы: 48

Бренд: T.I.P. Страницы: 108

Бренд: 2E Страницы: 26

Бренд: emaux Страницы: 21

Ephoca HPAC 2.0

Бренд: Innova Страницы: 40

Бренд: Emec Страницы: 44

Бренд: intensity Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды