Hoshizaki KM-340MAJ Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 38

background image

34

Sanitizing Rinse 1
19) Turn the cleaning valve to the right until completely horizontal (closed). Move the control

switch to the "ICE" position, then replace the front panel. After 3 min., remove the front
panel, then move the control switch to the "OFF" position.

20) Turn the cleaning valve to the left until completely vertical (open). Move the control

switch to the "WASH" position, then replace the front panel. After 5 min., remove the
front panel, then move the control switch to the "OFF" position.

21) Disconnect the water pump hose. After the water tank has drained, reconnect the water

pump hose.

Sanitizing Rinse 2
22) Turn the cleaning valve to the right until completely horizontal (closed). Move the control

switch to the "ICE" position, then replace the front panel. After 3 min., remove the front
panel, then move the control switch to the "OFF" position.

23) Turn the cleaning valve to the left until completely vertical (open). Move the control

switch to the "WASH" position, then replace the front panel. After 5 min., remove the
front panel, then move the control switch to the "OFF" position.

24) Disconnect the water pump hose. After the water tank has drained, reconnect the water

pump hose.

Sanitizing Rinse 3
25) Turn the cleaning valve to the right until completely horizontal (closed). Move the control

switch to the "ICE" position, then replace the front panel. After 3 min., remove the front
panel, then move the control switch to the "OFF" position.

26) Turn the cleaning valve to the left until completely vertical (open). Move the control

switch to the "WASH" position, then replace the front panel. After 5 min., remove the
front panel, then move the control switch to the "OFF" position.

27) Disconnect the water pump hose. After the water tank has drained, reconnect the water

pump hose. Replace the base cover.

28) Clean the dispenser unit/ice storage bin liner using a neutral cleaner. Rinse thoroughly

after cleaning.

29) Turn the cleaning valve to the right until completely horizontal (closed). Move the control

switch to the "ICE" position. Note: If on a dispenser unit, turn on the dispenser unit
power supply.

30) Replace all panels in their correct positions.

«
...
32
33
34
35
36
...
»

Содержание KM-340MAJ







































Отзывы:

Нет отзывов

Похожие инструкции для KM-340MAJ

Бренд: 9BARISTA Страницы: 8

Бренд: Taurus Страницы: 40

Бренд: Aztech Страницы: 2

Бренд: illy Страницы: 9

Бренд: Cafection Страницы: 82

Бренд: CASO DESIGN Страницы: 18

Бренд: camry Страницы: 76

Бренд: MUNBYN Страницы: 18

Бренд: Saeco Страницы: 2

Бренд: Quick Страницы: 24

Бренд: Krups Страницы: 56

Бренд: Axis Страницы: 16

Бренд: Ice-O-Matic Страницы: 2

Bakers Delight RHBM1500

Бренд: Russell Hobbs Страницы: 23

Бренд: Malongo Страницы: 84

Бренд: APW Wyott Страницы: 12

Бренд: Klarstein Страницы: 26

P-touch Extra PT-330

Бренд: Brother Страницы: 150

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды