manualshive.com logo in svg

Hoshizaki KM-251BAH, Руководство по обслуживанию

Поделиться
Скачать
Hoshizaki KM-251BAH Скачать руководство пользователя страница 26

26

Problem

Possible Cause

Remedy

b) Control Board

1. Defective.

1. See "II.C.6. Control Board 

Check Procedure."

[7] All components 

run, but no ice is 
produced.

a) Refrigerant

1. Undercharged.

1. Check for leaks and 

recharge.

2. Air or moisture 

trapped.

2. Replace drier and 

recharge.

b) Compressor

1. Defective valve.

1. Replace.

c) Hot Gas Valve

1. Continues to open in 

freeze cycle.

1. Check and replace.

d) Harvest Water Valve

1. Water valve is wide 

open during freeze.

1. Check for water leaks with 

icemaker off.

e) Water Valve Relay

1. Contacts stuck.

1. Replace.

2. Evaporator is Frozen Up

Problem

Possible Cause

Remedy

[1]Freeze cycle time is 

too long.

a)Float Switch

1. Leads shorted or 

defective switch.

1. Check and replace.

2. Float does not move 

freely.

2. Clean or replace.

b)Water Valves

1. Diaphragm does not 

close.

1. Check for water leaks with 

icemaker off.

c) Control Board

1. Defective.

1. See "II.C.6. Control Board 

Check Procedure."

[2]All ice formed on 

evaporator does not 
fall into bin in harvest 
cycle.

a)Evaporator

1. Scaled up.

1. Clean.

b)Water Supply Line

1. Water pressure too 

low.

1. Check and get 

recommended pressure.

c) Water Filter System

1. Dirty/Restricted

1. Replace filter.

d)Water Valves

1. Dirty mesh filter or 

orifice.

1. Clean.

2. Diaphragm does not 

close.

2. Check for water leaks with 

icemaker off.

e) Ambient and/or water 

temperature.

1. Too cool.

1. Increase temperature.

f) Thermistor

1. Out of position or 

loose attachment.

1. See "V.I. Removal 

and Replacement of 
Thermistor."

g)Control Board

1. Harvest timer is set 

too short.

1. Adjust longer, referring 

to "II.C.3. Controls and 
Adjustments, c) Harvest 
Timer. 

2. Defective.

2. See "II.C.6. Control Board 

Check Procedure."

[3]Other

a)Spray Tubes

1. Clogged.

1. Clean

2. Out of position.

2. Place in position.

b)Water System

1. Dirty.

1. Clean.

Содержание KM-251BAH












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды