Hoshizaki KM-2500SRH3 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 29

background image

2

IMPORTANT

Only qualified service technicians should attempt to install, service, or maintain
this icemaker. No installation, service, or maintenance should be undertaken
until the technician has thoroughly read this Instruction Manual. Likewise, the
owner/manager should not proceed to operate the icemaker until the installer
has instructed them on its proper operation. Failure to install, operate, and
maintain the equipment in accordance with this manual may adversely affect
safety, performance, and warranty coverage.

HOSHIZAKI provides this manual primarily to assist qualified service technicians in the
installation, maintenance, and service of the icemaker.

Should the reader have any questions or concerns which have not been satisfactorily
addressed, please call, write, or send an e-mail message to the HOSHIZAKI Technical
Support Department for assistance.

HOSHIZAKI AMERICA, INC.
618 Highway 74 South
Peachtree City, GA 30269

Attn: HOSHIZAKI Technical Support Department

Phone: 1-800-233-1940 Technical Service

(770) 487-2331

Fax: 1-800-843-1056

(770) 487-3360

E-mail: [email protected]

Web Site: www.hoshizaki.com

NOTE:

To expedite assistance, all correspondence/communication MUST include the

following information:

    • Model Number ________________________

    • Serial Number ________________________

• Complete and detailed explanation of the problem.

«
1
2
3
4
...
»

Содержание KM-2500SRH3






























Отзывы:

Нет отзывов

Похожие инструкции для KM-2500SRH3

Бренд: L'Equip Страницы: 2

Gaufres Premium

Бренд: Lagrange Страницы: 76

Бренд: Profi Cook Страницы: 58

Бренд: Clatronic Страницы: 42

Бренд: La Cimbali Страницы: 43

Бренд: La Pavoni Страницы: 8

EXPRESSBAKE 5847

Бренд: Sunbeam Страницы: 92

Kobalto espresso

Бренд: Necta Страницы: 6

Бренд: Dash Страницы: 32

Mini-Cappuccino

Бренд: Newco Страницы: 24

Бренд: STARBUCKS Страницы: 9

Бренд: Klarstein Страницы: 44

Бренд: Klarstein Страницы: 64

Бренд: Hendi Страницы: 118

Tassimo my way 2

Бренд: Bosch Страницы: 2

Бренд: Ice-O-Matic Страницы: 13

Бренд: LAVAZZA Страницы: 148

Бренд: Lagrange Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды