Hoshizaki KM-1100MAJ50 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 24

background image

9

Fig. 1

Front
Panel

Insulation
Panel

Top Panel

Side Panel (R)

B. Checks Before Installation

• Visually inspect the exterior of the shipping container and immediately report any

damage to the carrier. Upon opening the container, any concealed damage should also
be immediately reported to the carrier.

• Remove the shipping carton, tape, and packing material. If any are left in the appliance,

it will not work properly.

• See the nameplate on the rear panel, and check that your voltage supplied corresponds

with the voltage specified on the nameplate.

• Remove the panels to prevent damage when installing the appliance. See "II.C. How to

Remove Panels."

• Remove the package containing the accessories.
• Remove the protective plastic film from the panels. If the appliance is exposed to the

sun or to heat, remove the film after the appliance cools.

• Check that the refrigerant lines do not rub or touch lines or other surfaces, and that the

fan blade (if applicable) turns freely.

• Check that the compressor is snug on all mounting pads.
• The icemaker can be installed on a storage bin 30" wide or wider. Hoshizaki Ice Storage

Bins, Model B-500 series is recommended. For further options, contact your local
Hoshizaki distributor.

Model Number Bin Width

Recommended Hoshizaki Ice Storage Bin

KM-1100MAJ50 30" or Wider B-500 Series

For further options, contact your local Hoshizaki distributor.

C. How to Remove Panels

See Fig. 1

• Front Panel: Remove the screw. Lift up and

pull towards you.

• Top Panel: Lift up at front slightly, push

rearward and lift off.

• Right Side Panel: Remove the screw. Slide

forward slightly and lift off.

• Insulation Panel: Lift up slightly, and pull

towards you.

«
...
7
8
9
10
11
...
»

Содержание KM-1100MAJ50

























Отзывы:

Нет отзывов

Похожие инструкции для KM-1100MAJ50

Бренд: Havso Страницы: 24

Бренд: Hamilton Beach Страницы: 20

Бренд: Acopino Страницы: 42

Бренд: La Marzocco Страницы: 17

Бренд: Carimali Страницы: 20

Balanced Living YG2328US

Бренд: T-Fal Страницы: 24

CLASSE 11 Series

Бренд: Rancilio Страницы: 28

Бренд: Oki Страницы: 76

Бренд: tomado Страницы: 20

Бренд: Wittenborg Страницы: 12

Бренд: Bloomfield Страницы: 24

Бренд: Carnival King Страницы: 3

Бренд: Capresso Страницы: 12

Hotel Dispenser CD 40030 Series

Бренд: Ice-O-Matic Страницы: 21

Бренд: Sencor Страницы: 12

Бренд: DeLonghi Страницы: 14

ESPRESSO COFFEE MACHINE

Бренд: ZAGATO Страницы: 16

ESPRESSO EVOLUTION

Бренд: Gaggia Milano Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды