background image

17

III. Maintenance

The appliance must be maintained in accordance with the instruction manual and labels 
provided. Consult with your local Hoshizaki Certified Service Representative about 
maintenance service.

 WARNING

• Only qualified service technicians should service the appliance.
• To reduce the risk of electric shock, do not touch the control switch with damp 

hands.

• Move the control switch to the "OFF" position and turn off the power supply before 

servicing. Lockout/Tagout to prevent the power supply from being turned back on 
inadvertently.

 CHOKING HAZARD:

 Ensure all components, fasteners, and thumbscrews are 

securely in place after any maintenance is done to the appliance. Make sure that 
none have fallen into the dispenser unit/ice storage bin.

A. Maintenance Schedule

The maintenance schedule below is a guideline. More frequent maintenance may be 
required depending on water quality, the appliance's environment, and local sanitation 
regulations.

Maintenance Schedule

Frequency Area

Task

Daily

Scoop

Clean the ice scoop using a neutral cleaner. Rinse thoroughly after cleaning.

Bi-Weekly Air Filters

Inspect. Wash with warm water and neutral cleaner if dirty. 

Monthly

External Water 
Filters

Check for proper pressure and change if necessary.

Icemaker Exterior Wipe down with a clean, soft cloth. Use a damp cloth containing a neutral 

cleaner to wipe off oil or dirt build up. Clean any chlorine staining (rust 
colored spots) using a non-abrasive cleanser.

Underside of 
Icemaker and Top 
Kits; Bin Door

Wipe down with a clean cloth and warm water.

Yearly

Icemaker and 
Dispenser Unit/Ice 
Storage Bin

Clean and sanitize per the cleaning and sanitizing instructions provided in 
this manual. See "III.B. Cleaning and Sanitizing Instructions."

Water Supply Inlet Close the icemaker water supply line shut-off valve and drain the water 

system. Clean the water supply inlet screen.

Condenser

Inspect. Clean if necessary by using a brush or vacuum cleaner. More 
frequent cleaning may be required depending on location.

Water Hoses

Inspect the water hoses and clean/replace if necessary. 

Содержание KM-1100MAJ50

























Отзывы: