background image

1

1. TIMING CHART

IM-65LE-Q

Freeze

State

1,2

3

4

8

9

1,2

4

8

S1

A

ctuator Toggle Switch

Left (Arm Down

)

Right (Arm Up)

S2

Micro Switch (A

)

ON

(Water Pan control)

OFF

S3

Micro Switch (B

)

ON

(Cam control)

OFF

CM

Compresso

r

ON OFF

X5

CM/PM Cut Off Relay

ON OFF

FM

Fan Moto

r

ON OFF

PM

Pump Moto

r

ON OFF

A

CM

A

ctuator Moto

r

Down OFF Up

HV1

Hot Gas Valve

ON OFF

WV

Water Valve

ON OFF

Operation State 1,2

After power supply is turned on or freeze cycle completes, FM starts, water plate opens to reach cam actuating positio

n, and water supply begins for defrost cycle.

State 3

If water plate does not release ice after reaching cam actuating position, ACM and CM stop.

State 4

When water plate releases ice, WV closes and water plate starts to open further.

State 5

When water plate fully opens and S1 moves to left (arm down) position, HV opens. When 3 minutes passes after CM stops in

 [state 2], CM restarts.

State 6

Cube control thermistor senses temperature higher than defrost setting, water plate starts to close and water supply beg

ins.

State 7

When water plate closes and S1 moves to right (arm up) position, water supply stops and PM starts.

State 8

When 15 seconds passes after S1 moves to right (arm up) position, FM starts and PM stops to start freezing.

State 9

When cube control thermistor senses temperature lower than freeze setting, [state 1] begins.

Defrost

5,6

7

Defrost

Freeze

5,6

7

3

th < freeze setting

15 sec

th > defrost setting

15 sec

th > defrost setting

Содержание IM-65LE-Q








Отзывы: