Hoshizaki HR24B Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 39

background image

12

C. Display Module Icons

Display module icons inform you of energized components and if the appliance is in
alarm.

Display Module Icons

Icon

Meaning

Compressor

Steady: Compressor running.

Flashing:

•

Compressor delay timer. Compressor starts within 2 min.

•

While adjusting cabinet temperature setpoint. For cabinet temperature setpoint

adjustment, see "II.B Cabinet Temperature and Defrost."
Defrost

Appliance is in defrost cycle. See "II.F.3.10) Defrost" for details.
Evaporator Fan Motor

Evaporator fan motor is running. Evaporator fan motor de-energizes when door is open.
During energy saving mode, evaporator fan motor cycles with compressor. When compressor is
de-energized, evaporator fan motor cycles 1 min. on and 5 min. off.
Alarm

Appliance is in alarm. See "II.I. Alarm Safeties" for details.

D. Control Panel Lockout

The control panel can be locked to help prevent the appliance from being turned off or
the setpoint from being changed inadvertently.
To lock the control panel, press and hold the "-" button and the power button until "Loc"
appears briefly on the display module.
To unlock the control panel, press and hold the "-" button and the power button until
"UnL" appears briefly on the display module.

«
...
10
11
12
13
14
...
»

Содержание HR24B








































Отзывы:

Нет отзывов

Похожие инструкции для HR24B

Бренд: Zanussi Страницы: 24

Бренд: Samsung Страницы: 104

Бренд: Zanussi Страницы: 12

Бренд: Zanussi Страницы: 24

Бренд: TECO Страницы: 18

Бренд: Rangemaster Страницы: 40

Le Maitre JGI4421

Бренд: JUNO Страницы: 10

Бренд: Montgomery Ward Страницы: 8

Бренд: Galanz Страницы: 6

Бренд: Aegis Страницы: 12

Бренд: INVENTOR Страницы: 36

Бренд: Haier Страницы: 30

HSE01WNA - 02-03

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 34

Бренд: Haier Страницы: 49

Бренд: Haier Страницы: 313

Бренд: Haier Страницы: 31

Бренд: Electrolux Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды