manualshive.com logo in svg

Hoshizaki F-330BAH, Руководство по обслуживанию

Поделиться
Скачать
Hoshizaki F-330BAH Скачать руководство пользователя страница 20

20

6) While not necessary, the floats can be removed from the shaft during cleaning. If you 

remove them, note that the blue float is on top (UFS) and the white float is on bottom 
(LFS). The floats must be installed with the magnets inside them towards the top of the 
switch. See Fig. 2. Installing the floats upside down will affect the timing of FS operation. 

7) Rinse the float switch assembly thoroughly with clean water and replace in its correct 

position.

8) Replace the rear and top panels in their correct positions. 

9) Plug the appliance into the electrical outlet, then move the power switch to the "ON" 

position to start the automatic icemaking process.

10) Replace the front panel in its correct position.

Legend: 

FS

–float switch; 

LFS

–lower float switch;

 UFS

–upper float switch

Reservoir

Reservoir Cover

Float Switch Assembly

Red (R) 

(upper float switch)

Black (BK) 

(common)

Dark Blue (DBU) 

(lower float switch)

Upper Float (blue)

Magnet (towards top)

Magnet (towards top)

Lower Float (white)

Plastic Retainer Clip

Spring Retainer Clip

Fig. 1

Fig. 2

Содержание F-330BAH


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды