Horizon Hobby JR 11X Скачать руководство пользователя страница 21

40

JR 11X • RADIO INSTRUCTION MANUAL

41

JR 11X • RADIO INSTRUCTION MANUAL

a.  Exercise vigilance in locating full-scale aircraft (get help if possible) so as not to 

create a collision hazard.

b.  Select an operating site at sufficient distance from populated areas so you do 

not create a noise problem or a potential hazard.

c.  Do not fly higher than 400 feet above the surface.
d.  Always operate more than three miles from the boundary of an airport unless 

you are given permission to be closer by the appropriate air traffic control 
facility in the case of an airport for which a control zone has been designated or 
by the airport manager in the case of other airports.

e.  Do not hesitate to ask for assistance in complying with these guidelines at the 

airport traffic control tower or air route traffic control center nearest the site of 
your proposed operation.

Information Provided By

Director, Air Traffic Service Federal Aviation Administration, Washington, D.C.

Daily Flight Checks

1.  Check the battery voltage on both the transmitter and the receiver battery 

packs. Do not fly below 4.3V on the transmitter or below 9V on the receiver. 
To do so can crash your aircraft.

 

Note

: When you check these batteries, ensure that you have the polarities 

correct on your expanded scale voltmeter.

2.  Check all hardware (linkages, screws, nuts, and bolts) prior to each day’s 

flight. Be sure that binding does not occur and that all parts are properly 
secured.

3.  Ensure that all surfaces are moving in the proper manner.
4.  Perform a ground range check before each day’s flying session.
5.  Prior to starting your aircraft, turn off your transmitter, then turn it back 

on. Do this each time you start  your aircraft. If any critical switches are on 
without your knowledge, the transmitter alarm will warn you  at this time.

6.  Check that all trim levers are in the proper location.
7.  All servo pigtails and switch harness plugs should be secured in the 

receiver. Make sure that the switch harness moves freely in both directions.

WARRANTY AND  

REPAIR POLICY

WARRANTY PERIOD

Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties 

that the Products purchased (the “Product”) will be free from 

defects in materials and workmanship for a period of 3 (three) 

years from the date of purchase by the Purchaser. 

3 yeAR LIMITeD WARRANTy

Horizon reserves the right to change or modify this 

warranty without notice and disclaims all other 

warranties, express or implied.

(a) This warranty is limited to the original Purchaser 

(“Purchaser”) and is not transferable. REPAIR OR 

REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS 

THE EXCLUSIVE REMEDY OF THE PURCHASER.  

WARRANTY SERvICES

QUeSTIONS, ASSISTANCe, AND RePAIRS

Your local hobby store and/or place of purchase cannot 

provide warranty support or repair. Once assembly, setup 

or use of the Product has been started, you must contact 

Horizon directly. This will enable Horizon to better answer 

your questions and service you in the event that you may 

need any assistance. For questions or assistance, please 

direct your email to [email protected], or 

call 877.504.0233 toll free to speak to a Product Support 

representative.  You may also find information on our website 

at www.horizonhobby.com.

INSPECTION OR REPAIRS

If this Product needs to be inspected or repaired, please 

use the Horizon Online Repair Request submission process 

found on our website or call Horizon to obtain  a Return 

Merchandise Authorization (RMA) number. Pack the Product 

securely using a shipping carton. Please note that original 

boxes may be included, but are not designed to withstand 

the rigors of shipping without additional protection. Ship 

via a carrier that provides tracking and insurance for lost 

or damaged parcels, as Horizon is not responsible for 

merchandise until it arrives and is accepted at our facility. An 

Online  Repair Request is available at www.horizonhobby.com 

http://www.horizonhobby.com under the Repairs tab. If you 

do not have internet access, please contact Horizon Product 

Support to obtain a RMA number along with instructions 

for submitting your product for repair.  You will be asked to 

provide your complete name, street address, email address 

and phone number where you can be reached during 

business days, your RMA number, a list of the included 

items, and a brief summary of the problem upon submission. 

Your original sales receipt must also be included for warranty 

consideration. Be sure your name, address, and RMA number 

are clearly written on the outside of the shipping carton.

WARRANTY INSPECTION AND REPAIRS

To receive warranty service, you must include your 

original sales receipt 

verifying the proof-of-purchase 

date. Provided warranty conditions have been met, your 

Product will be repaired or replaced free of charge. Repair or 

replacement decisions are at the sole discretion of Horizon 

Hobby.

Notice:

 Do not ship batteries to Horizon Hobby. If you 

have any issue with a battery, please contact the appropriate 

Horizon Product Support office.

This warranty covers only those Products purchased from an 

authorized Horizon dealer. Third party transactions are not 

covered by this warranty. Proof of purchase is required for 

warranty claims. 

(b) Limitations- HORIZON MAKES NO WARRANTY OR 

REPRESENTATION, EXPRESS OR IMPLIED, ABOUT 

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS 

FOR A PARTICULAR PURPOSE OF THE PRODUCT. THE 

PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE 

DETERMINED THAT THE PRODUCT WILL SUITABLY MEET 

THE REQUIREMENTS OF THE PURCHASER’S INTENDED 

USE.

(c) Purchaser Remedy- Horizon’s sole obligation hereunder 

shall be that Horizon will, at its option, (i) repair or (ii) 

replace, any Product determined by Horizon to be defective. 

In the event of a defect, these are the Purchaser’s exclusive 

remedies. Horizon reserves the right to inspect any and 

all equipment involved in a warranty claim. Repair or 

replacement decisions are at the sole discretion of Horizon. 

This warranty does not cover cosmetic damage or damage 

due to acts of God, accident, misuse, abuse, negligence, 

commercial use, or modification of or to any part of the 

Product. This warranty does not cover damage due to 

improper installation, operation, maintenance, or attempted 

repair by anyone other than Horizon. Return of any goods 

by Purchaser must be approved in writing by Horizon before 

shipment.

DAMAGE LIMITS

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT 

OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS 

OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY 

CONNECTED WITH THE PRODUCT, WHETHER SUCH CLAIM 

IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE, OR 

STRICT LIABILITY. Further, in no event shall the liability of 

Horizon exceed the individual price of the Product on which 

liability is asserted. As Horizon has no control over use, 

setup, final assembly, modification or misuse, no liability 

shall be assumed nor accepted for any resulting damage or 

injury. By the act of use, setup or assembly, the user accepts 

all resulting liability.

If you as the Purchaser or user are not prepared to accept 

the liability associated with the use of this Product, you 

are advised to return this Product immediately in new and 

unused condition to the place of purchase.

Law: These Terms are governed by Illinois law (without 

regard to conflict of law principals).

NON-WARRANTY REPAIRS

Should your repair not be covered by warranty 

the repair will be completed and payment will be 

required without notification or estimate of the 

expense unless the expense exceeds 50% of the 

retail purchase cost. 

By submitting the item for repair 

you are agreeing to payment of the repair without notification. 

Repair estimates are available upon request. You must 

include this request with your repair. Non-warranty repair 

estimates will be billed a minimum of ½ hour of labor. In 

addition you will be billed for return freight. Please advise us 

of your preferred method of payment. Horizon accepts money 

orders and cashiers checks, as well as Visa, MasterCard, 

American Express, and Discover cards. By submitting any 

item to Horizon for inspection or repair, you are agreeing to 

Horizon’s Terms and Conditions found on our website under 

the Repairs tab.

 Please note: non-warranty repair is 

only available on electronics and model engines.

Notice:

 Electronics and engines requiring inspection or 

repair should be shipped to the following address:
Horizon Service Center 

4105 Fieldstone Road 

Champaign, Illinois 61822, USA
All other Products requiring warranty inspection or repair 

should be shipped to the following address:
Horizon Product Support 

4105 Fieldstone Road 

Champaign, Illinois 61822, USA

Please call 877-504-0233 with any questions or 

concerns regarding this product or warranty.

Содержание JR 11X
























Отзывы: