18
JR 11X • RADIO INSTRUCTION MANUAL
19
JR 11X • RADIO INSTRUCTION MANUAL
SWASHPLATE TYPE
The Swashplate Type function enables the 11X to operate six different types of
swashplate control systems. The Swashplate options are:
• 1 Servo NORM standard mechanical mixing type
• 2 Servo/180°
• 3 Servo/120° CCPM (most popular)
• 3 Servo/140° CCPM (JR Vibe 50/90SG)
• 3 Servo/90° CCPM
• 4 Servo/90° CCPM
To Select a Swashplate Type
1. In the System Menu, highlight and select Swash Type using the Roller.
2. Highlight and select the displayed swashplate to access the available
swashplate types.
3. Select the desired swashplate.
FLIGHT MODeS (SAILPLANe)
A Flight Mode represents an aircraft configuration (camber position, trim
positions, Dual Rate/Expo settings, program mixes, aileron differential value,
etc.) that is programmed to optimize the aircraft for a particular task. Up to 5 flight
modes are available in the 11X that include Launch, Normal, Reflex, Thermal and
Float.
The objective of programming Flight Modes is to provide the ability to select a
switch position to activate a collection of settings that are optimized to perform
a particular task. For example, the launch mode is typically set up to give the
following:
• The flaps and flaperons are preset with positive camber to give more lift
during launch.
• An elevator preset trim position that gives the best climb is programmed.
• A high rudder rate with reduced exponential to give authoritative steering
control on launch is desired, while the elevator and aileron rates are set to
give a medium response.
• Aileron-to-rudder mix is turned off, as are landing flaps and elevator-
to-flap mix. Camber adjustment of the side lever is programmed to give
proportional camber changes to allow for last minute adjustments based on
wind and winch conditions.
• Aileron differential is set at 50%.
You can select all programming parameters by moving one switch. You can
assign most of the switch-selectable functions in the 11X to one or more Flight
Modes. Some of these functions include: Flaperon Mix, Servo Speed, Camber
system, Differential, Aileron to rudder mix, Elevator to flap mix, Flap rate, Brake
system, trims and programmable mixes. This provides the ability to have up to
5 completely different aircraft configurations that are selectable in flight using
switches.
When 3 Flight Modes are activated, you can select them during flight by using
one of seven 3-position switches: Flight mode switch, Motor switch, Butterfly
switch, Rudder D/R switch, Elevator D/R switch, Aux 2 switch, Aileron D/R switch
or Inhibit.
To activate the 2 Extra flight modes, the 4th and 5th flight modes are assigned
to one of the following switches: Flight Mode, Rudder D/R switch, Elevator
D/R switch, Flap Switch, Aux 2 switch, Aileron D/R switch, Inhibit. Flight mode
switches are selected and activated in the Device SEL function in the System
menu. Once Flight Modes are activated, you can use the Flight Mode switch to
select up to 4 Dual Rates and Exponential settings for each of the primary controls
(ELEV, AILE, RUDD). But you can continue to control Dual Rates and Exponential
settings by the 3 individual Dual Rate switches. You can assign all other functions
that can be activated by a switch to 1 or more Flight Modes when Flight Modes
have been activated.
ACTIvATING AND ASSIGNING
PRIMARY fLIGHT MODES
In the factory default setting, all flight modes are inhibited. Flight modes are
activated and assigned to the desired switch position using the REFLEX and
LAUN functions in the Device SEL screen.
In system mode list rotate the Roller until Device SEL is highlighted. Press the
Roller to access the Device Select screen.
To activate the launch, normal and float mode, rotate the Roller until LAUNCH is
highlighted then press the Roller. The following screen appears:
At this point, you must decide which 3-position switch you prefer to assign the
flight mode to. When a 3-position switch is selected, launch, cruise and land
will be activated. We recommend starting with the Flight Mode Switch (left
top 3-position switch), as this is a convenient place. Rotate the Roller until the
desired switch is highlighted; press to select. Alternatively, once you have the
switch options displayed, move the desired switch to automatically select the
switch.
ACTIvATING AND ASSIGNING
ADDITIONAL fLIGHT MODES
To activate the speed and thermal flight modes, highlight INH next to REFLEX and
press the Roller to select the desired switch position. Alternatively, once you have
the switch options displayed, move the desired switch to automatically select the
switch.
Important:
When the Reflex and Thermal flight modes are activated, launches
always have priority. Any time Launch is selected, it will override Reflex, Thermal
or Normal. To access Reflex or Thermal, the Launch switch must be in the middle
position. Try selecting the various flight modes several times while looking at the
main info screen to become familiar with the switch priority.
Note:
On the main info screen, the active flight mode will display on the top
center of the screen.
MOTOR fUNCTION
You can assign the motor function to operate from several different switches,
buttons or the Spoiler stick. In Device Select, highlight GEAR SW and press
the Roller to access the available outputs for the gear switch. Select the desired
output by highlighting it and press the Roller ( the output options will not be
accessible if the gear channel has been used as a mate for another channel).
Note:
Also see Motor System on page 29 for more details.
fLAP AND AUX fUNCTIONS
You can assign the Flap, Gear and Auxiliary channels to operate from several
different switches, buttons or the throttle stick. In Device Select, highlight the
desired Flap, Gear or Aux function. Next, press the Roller to access the available
switches you can program to operate each function. . In this selection screen
you can also set the 2 top trimmers to work as 2-position switches, 3-position
switches, or as momentary switches for a selected channel.
Select the desired switch by highlighting it then press the Roller.
ACTIvATING/INHIbITING CHANNELS
You can inhibit Channels 5 through 11, allowing them to be used as slave
channels, in programmable mix. Highlight the desired ACT/INH next to the
appropriate channel. Press the Roller to inhibit or activate the channel.
WING TYPE
The Wing Type function programs wing and tail types. The Wing Type program
allows the activation of V-tail, tip ailerons, dual elevators, dual rudders, dual flaps
and dual spoilers.
Note: In order to activate any of the Dual Mate functions (dual elevator, rudder or
flaps), the channels must be inhibited in Device Select.
To access Wing type
1. In the System List, rotate the Roller to highlight Wing Type. Press the Roller
to access the wing type screen.
2. If your sailplane has a V-tail, highlighting INH and press the Roller to
activate the V-tail function.
3. If your sailplane has dual elevators, dual rudders or dual flaps, highlight INH
under the desired channel and press the Roller to access a list of channels to
use as a mated channel. Highlight the channel and press the roller to accept.
.
fLAP STICK DIRECTION
You can use the Flap Stick Direction to reverse the direction of the Flap Stick
depending on whether you fly the stick high or low.
To reverse the direction of the Spoiler Stick
1. In the System List, rotate the Roller to highlight FLAP STK DIR. Press the
Roller to access the Flap Stick Direction screen.
2. Highlight FLAP on the screen and press the roller to reverse the direction of
the flap stick.
fUNCTION LIST
The Function List is used to complete the setup and adjust the aircraft’s flight
characteristics. Functions include Servo Reversing, Travel Adjust, Dual Rate and
Expo, Sub-Trim, Servo Speed and Programmable Mix functions, etc. Many of
these functions are frequently used to adjust the flight characteristics during setup
and at the field.
To Enter the function List
With the transmitter on Press LIST and the Function List will appear.
DUAL RATE AND EXPONENTIAL
Four dual and exponential rates are available and selectable via flight modes or
selected switches.
To Program Dual Rate and Exponential values
1 Highlight and select D/R & EXP in the Function List to obtain the Dual Rate
and Exponential display.
2 Highlight and select the desired channel values (Aileron, Elevator or
Rudder), noting that 4 sets of values display. If using the Dual Rate
switches, only 3 of the 4 values (pos0 through pos2) are active.