Horizon Fitness Super Cub dsm Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 29

Horizon Fitness Super Cub dsm Скачать руководство пользователя страница 6

6

HobbyZone Super Cub • Instruction Manual

Install Battery in Model

The battery for your Super Cub LP has a blue EC3™ power connector and a
small white balance charging connector. Always connect only the blue connector
to your model.

WARNING:

Only connect the white balance charging connector to a

battery charger. NEVER connect to X-Port receptacle on the bottom of

the fuselage or the model will be damaged.

Keep the X-Port socket covered except when in use with approved accessories.
See X-Port information in this manual for use of available accessories.

1. Move the battery door latch and open the battery door on the bottom of the

fuselage.

2. Carefully put battery in battery compartment.
3. Close the hook and loop strap over the battery.
4. When ready to bind or operate the model, connect the blue EC3 battery

connectors in the model.

5. Close the battery door and move the latch to keep the door closed.

1

3

2

«
...
4
5
6
7
8
...
»

Содержание Super Cub dsm






























Отзывы:

Нет отзывов