manualshive.com logo in svg

Horizon Fitness Super Cub dsm, Инструкция по эксплуатации, Страница: 23 / 29

Поделиться
Скачать
Horizon Fitness Super Cub dsm Скачать руководство пользователя страница 23

23

HobbyZone Super Cub • Instruction Manual

Problem

Possible Cause

Solution

Aircraft will not respond to throttle 

but responds to other controls

Throttle not at idle and/or throttle trim too high

Reset controls with throttle stick and throttle trim at lowest setting

Throttle channel is reversed

Reverse throttle channel on transmitter

Extra propeller noise or extra 

vibration

Damaged propeller and spinner, gear shaft or motor

Replace damaged parts

Propeller is out of balance

Balance or replace propeller

Reduced flight time or aircraft 

underpowered

Flight battery charge is low

Completely recharge flight battery

Propeller installed backwards

Install propeller with numbers facing forward

Flight battery damaged

Replace flight battery and follow flight battery instructions

Flight conditions may be too cold

Make sure battery is warm before use

Battery capacity may be low for flight conditions

Replace battery or use a larger capacity battery

Aircraft will not link to transmitter

Transmitter too near aircraft during binding process

Move powered transmitter a few feet from aircraft, 

 

disconnect and reconnect flight battery to aircraft

Aircraft not bound to transmitter

Bind transmitter to aircraft receiver

Aircraft bound to different model memory

 

(ModelMatch radios only)

Select correct model memory on transmitter

Flight battery/Transmitter battery charge is too low

Replace/recharge batteries

Control surface does not move

Control surface, control horn, linkage or servo damage

Replace or repair damaged parts and adjust controls

Wire damaged or connections loose

Do a check of wires and connections, connect 

 

or replace as needed

Transmitter not bound correctly

Bind transmitter to aircraft receiver

Control trim out of adjustment

Adjust trims to restore full control

Controls reversed

Transmitter settings reversed

Do the Control Direction Test and adjust controls on transmitter appropriately

Motor loses power

Damage to motor, propeller shaft or power components

Do a check of batteries, transmitter, receiver, motor and wiring for damage 

 

(replace as needed)

Motor power pulses then motor 

loses power

ESC uses default LVC

Recharge flight battery or replace battery 

 

that is no longer performing

Troubleshooting Guide, continued

Содержание Super Cub dsm






























Отзывы:

Нет отзывов