Horizon Fitness CRF-362 Скачать руководство пользователя страница 84

Страница: 84 / 122

If an Error Code Is Displayed

CRF-362

Error Code

Description

Causes and Solutions

102

Transport Section Cover

Open (Cover Switch S12)

Close the cover.

103

Front Cover Open

(Cover Switch S13)

Close the cover.

200

Feed Table Overlimit Error

The feed section upper guide was lifted up while the feed table was rising.

13130

40201A1

Feed Section Upper Guide

Lower the feed table and then check if there is no foreign object be-

tween the feed table and the feed section upper guide.

201

Feed Table Movement Error

The feed table could not move up and down.

Check if there is no object preventing the feed table from moving up

and down.

210

Misfeed

A sheet was not fed. If the same error occurs repeatedly, see page

89 and follow the instructions.

211

Double Feed

A double feeding occurred. If the same error occurs repeatedly, see

page 89 and follow the instructions.

212

Sheet Feed Section Jam

(Sensor B13 is on before

operation.)

A sheet was detected when

is pressed. Remove the sheet.

213

The Transport Interval Is Too

Narrow

See page 70 and set the transport interval larger.

300

Jam

(The sheet did not arrive at

sensor B30.)

A jam has occurred in the register transport section. Remove the

sheet. If the same error occurs repeatedly, see page 90 and solve

the problem.

301

Jam

(Sensor B14 is on before

operation.)

A sheet was detected when

is pressed.

Remove the sheet.

If this error code is displayed even though no sheets are jammed, the

sensor may be dirty. Check that the sensor works properly using the

Information - Monitor screen. (See page 39 .)

310

Too Many Sheets at Regis-

tration Transport Section

Before a sheet was detected by the B30 creasing section sheet leading

edge sensor, the next sheet was detected by the B13 double feed sen-

sor.

Remove the sheet.

If the same error occurs repeatedly, set the transport interval larger.

(See page 70 .)

Содержание CRF-362



























































































































Результаты поиска

Содержание CRF-362

Отзывы:

Бренды по названию

Популярные бренды

Horizon Fitness CRF-362, Руководство пользователя

Результаты поиска

Содержание CRF-362

Отзывы:

Бренды по названию

Популярные бренды