horiba LAQUAact-PD110 Скачать руководство пользователя страница 34

Страница: 34 / 117

Preparation

• Using the AC adapter (option)

It is possible to use the AC adapter to operate the instrument.
Perform the following procedure to connect AC adapter to the instrument.
The AC adapter is an option. To purchase it, contact your dealer. (Refer to "Options"
(page 100).)

1. Open the AC adapter cover of the

instrument.

2. Insert the AC adapter cable by

fitting with the AC adapter jack of in
the instrument.

3. Insert AC adapter into the electrical

socket.

Note

・

Do not insert the cable with force when the connector does not match the jack.

・

When not using the AC adapter, close the AC adapter connector cover.

・

While the AC adapter is connected, the instrument does not have the dust-proof and

waterproof performance. Dust or moisture could get inside the instrument, possibly
causing instrument malfunction.

AC adapter jack

Содержание LAQUAact-PD110






















































































































Результаты поиска

Содержание LAQUAact-PD110

Отзывы:

horiba LAQUAact-PD110, Инструкция по эксплуатации, Страница: 34 / 117

Результаты поиска

Содержание LAQUAact-PD110

Отзывы: