horiba LAQUAact-PD110 Скачать руководство пользователя страница 102

Страница: 102 / 117

When an error message appears

●

ERR No.0002

Empty battery level

The instrument cannot operate properly because the battery level is empty.

●

ERR No.0004

Asymmetric potential error

Detected that the asymmetric potential of the electrode is out of the setting range that
allows proper measurement.

Cause

How to solve problem

The battery level is empty.

Replace the batteries or connect the AC adapter (option).

Cause

How to solve problem

The electrode is dirty.

Clean the electrode.

The electrode is cracked.

Replace the electrode.

The standard solution
concentration is fluctuating.

Replace the internal solution in the reference electrode.

The electrode is not connected
correctly.

Connect the electrode correctly.

Electrode is not immersed
enough to cover liquid junction.

The electrode must be immersed up to the liquid junction.
As a guide, immerse to at least 3 cm from the tip of the
electrode.

There is a problem with the
standard solution.

Use new standard solution.

Содержание LAQUAact-PD110






















































































































Результаты поиска

Содержание LAQUAact-PD110

Отзывы:

horiba LAQUAact-PD110, Инструкция по эксплуатации, Страница: 102 / 117

Результаты поиска

Содержание LAQUAact-PD110

Отзывы: