HopeRF RF 65 Скачать руководство пользователя страница 41

Страница: 41 / 72

Page 41

RF65

Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: [email protected] http://www.hoperf.com

ADVANCED COMMUNICATIONS & SENSING

DATASHEET

Rx DATA
(NRZ)

Bit N-x =

Sync_value[x]

Bit N-1 =

Sync_value[1]

Bit N =

Sync_value[0]

DCLK

SyncAddressMatch

Figure 24. Sync Word Recognition

During the comparison of the demodulated data, the first bit received is compared with bit 7 (MSB) of

RegSyncValue1

and

the last bit received is compared with bit 0 (LSB) of the last byte whose address is determined by the length of the Sync
word.

When the programmed Sync word is detected the user can assume that this incoming packet is for the node and can be
processed accordingly.

SyncAddressMatch

is cleared when leaving Rx or FIFO is emptied.

5.2.3.2. Configuration



Size: Sync word size can be set from 1 to 8 bytes (i.e. 8 to 64 bits) via

SyncSize

RegSyncConfig



Error tolerance: The number of errors tolerated in the Sync word recognition can be set from 0 to 7 bits to via

SyncTol



Value: The Sync word value is configured in

SyncValue(63:0)

Note

SyncValue choices containing 0x00 bytes are not allowed

5.2.4. Packet Handler

The packet handler is the block used in Packet mode. Its functionality is fully described in section 5.5.

5.2.5. Control

The control block configures and controls the full chip's behavior according to the settings programmed in the configuration
registers.

Содержание RF 65









































































Результаты поиска

Содержание RF 65

Отзывы:

Похожие инструкции для RF 65

Бренды по названию

Популярные бренды

HopeRF RF 65, Руководство пользователя

Результаты поиска

Содержание RF 65

Отзывы:

Похожие инструкции для RF 65

Бренды по названию

Популярные бренды