HopeRF RF 65 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 72

background image

Page 16

RF65

Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: [email protected] http://www.hoperf.com

F

=

XO S C

ADVANCED COMMUNICATIONS & SENSING

DATASHEET

3.3.2. CLKOUT Output

The reference frequency, or a fraction of it, can be provided on DIO5 (pin 13) by modifying bits

ClkOut

in

RegDioMapping2

.

Two typical applications of the CLKOUT output include:



To provide a clock output for a companion processor, thus saving the cost of an additional oscillator. CLKOUT can be

made available in any operation mode except Sleep mode and is automatically enabled at power on reset.



To provide an oscillator reference output. Measurement of the CLKOUT signal enables simple software trimming of the

initial crystal tolerance.

Note

to minimize the current consumption of the RF65, please ensure that the CLKOUT signal is disabled when not

required.

3.3.3. PLL Architecture

The frequency synthesizer generating the LO frequency for the receiver is a fractional-N sigma-delta PLL. The PLL
incorporates a third order loop capable of fast auto-calibration, and it has a fast switching-time. The VCO and the loop filter
are both fully integrated, removing the need for an external tight-tolerance, high-Q inductor in the VCO tank circuit.

3.3.3.1. VCO

The VCO runs at 2, 4 or 6 times the RF frequency (respectively in the 915, 434 and 315 MHz bands) to reduce any LO
leakage in receiver mode, to improve the quadrature precision of the receiver.

The VCO calibration is fully automated. A coarse adjustment is carried out at power on reset, and a fine tuning is
performed each time the RF65 PLL is activated. Automatic calibration times are fully transparent to the end-user, as their
processing time is included in the

TS_RE

specifications.

3.3.3.2. PLL Bandwidth

The bandwidth of the RF65 Fractional-N PLL is wide enough to allow for very fast PLL lock times, enabling both short
startup and fast hop times required for frequency agile applications.

3.3.3.3. Carrier Frequency and Resolution

The RF65 PLL embeds a 19-bit sigma-delta modulator and its frequency resolution, constant over the whole frequency
range, and is given by:

F

S TE P

----------------

2

19

The carrier frequency is programmed through

RegFrf

, split across addresses 0x07 to 0x09:

F

R F

=

F

STEP

×

Frf

(23,0)

Note

The Frf setting is split across 3 bytes. A change in the center frequency will only be taken into account when the

least significant byte FrfLsb in RegFrfLsb is written.

«
...
14
15
16
17
18
...
»

Содержание RF 65









































































Отзывы:

Нет отзывов

Похожие инструкции для RF 65

Бренд: Zamel Страницы: 34

Бренд: Z3 Technology Страницы: 16

Бренд: Yaesu Страницы: 195

Бренд: Yaesu Страницы: 39

Бренд: Samson Страницы: 15

Бренд: Harman Kardon Страницы: 28

Бренд: Boss Audio Systemsu Страницы: 33

Бренд: Immersion Страницы: 5

Бренд: Easy wave Страницы: 4

Бренд: VDO Страницы: 18

Prestige Home Theater Sytem

Бренд: Audiovox Страницы: 4

Бренд: BUXTON Страницы: 40

Бренд: VDO Страницы: 2

HP450 2A Rugged

Бренд: Alan Страницы: 174

Бренд: NAD Страницы: 46

Бренд: Velleman-Kit Страницы: 28

Бренд: VDO Страницы: 2

Бренд: Kanga Products Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды