Hoover Robo.com3, Руководство пользователя

Страница: 10 / 14

GB
* Certain Models only ** May vary according to model 10
Home Mode : [Fig.15]
You can command your Robo.com³ return to the charging station for charging by:
1) Press the sensitive touch control on the robot
2) Press the button on the remote control
3) Following the instruction in the wi-Fi Application*.
ADDitioNAL FeAtUres
Demo Mode:
with remote control
Press the demo button once to start the product demonstration. This will start
in Loop mode. To stop the demonstration presses the demo button again.
With Wi-Fi Application*
From the menu press demo button.
FLoor PoLisHer PAD*:
[Fig.16]
Attached via the floor polisher pad holder* to the underside of Robo.com³, the floor polisher pad holder*
is used to polish marble, parquet, wooden and other delicate Flooring.
Note: Do not use on a carpeted surface.
MAINTAININg YOUR ROBO.COM³ CLEANER
Before performing any maintenance task, ensure the Robo.com³ is switched off.
1. Turn the Robo.com³ off and remove it from the charging station.
2. Use a damp cloth with a little soap to clean all surfaces. DO NOT allow water into any part of the
product whilst cleaning.
3. Dry with a soft cloth.
eMPtyiNG tHe DUst CoNtAiNer
Empty the dust container every cleaning cycle or when it is full.
1. Turn the Robo.com³ off and remove from the charging station.
2. Press the dust container release button and remove the dust container from the Robo.com³.
3. Hold the dust container over a bin to empty.
4. Use the multi-purpose cleaning brush when necessary to remove any excess dust from the internal
surface of the dust container.
5. Refit the dust container to the Robo.com³.
CLeANiNG tHe FiLters
[Fig.17]
The Robo.com³ is fitted with a pre-motor filter. To maintain optimum cleaning performance, regularly
clean the pre-motor filter.
T he pre-motor filter should be cleaned every 5 dust container empties and
should be washed.
iMPortANt: T he pre-motor filter should be cleaned and washed after the dust container has been
emptied 5 times. Failure to clean your filter may result in air blockage overheating and product failure.
This may invalidate your guarantee.
1. Turn the Robo.com³ off and remove from the charging station.
2. Press the dust container release button and remove the dust container from the Robo.com³.
3. Pull the filter drawer tab to open the filter drawer.
4. Pull the side of the filter to pop it out of the bracket.
5. Gently tap and wash the filter using hand warm water. Remove excess water from the filter with a
dry cloth and leave to dry.
6. Reassemble once completely dry and refit to the Robo.com³. DO NOT use the Robo.com³ without a
pre-motor filter fitted.
iMPortANt: Regularly check and maintain the pre-motor filter by following the filter maintenance
instructions, it is also recommended that you purchase new filters after every 3 filter washes. This will
maintain your Robo.com³ performance.
CLeAN FiLter reGULArLy >>>PULL to ACCess tHe FiLter>
CLeANiNG tHe AGitAtors
Clean the agitators regularly to maintain maximum cleaning performance.
1. Turn Robo.com³ off and remove it from the charging station.
2. Turn the Robo.com³ over.
3. Rotate the agitators assembly carefully and using scissors cut and remove any tangled threads or hair etc.
4. Use the multi-purpose cleaning brush to remove any excess dust.
rePLACiNG tHe AGitAtors [Fig.18]
1. Switch the Robo.com³ off and turn it over.
2. Use screw driver to loosen agitator holder screw and remove it
3. Remove both agitators
4. Clean the recess where the agitators sit.
5. Refit the new agitators, ensuring they sit correctly.
6. Refit agitator holder and fasten it.
DEMO
DEMO
DEMO
Fig.15
Fig.16
Fig.17
Fig.18