For the cookers below written adjustment have to be done by qualified
technician.
Follow the steps given below to convert the appliance from the factory
set up to that for a different gas type.
Cookers are adjusted NG and connection type
is cylindric (1). For hose type NG connection,
hose adapter (2) can be fixed to cylindrical
adapter with seal.
For LPGconnection, LPGhose adapter (3) can
be fixed to cylindric adapterwith seal.
Adjustments and changing injectors
Changing Injectors
•Remove grates.
•Remove burner caps and burners.
•Remove injectors by using a 7 mm wrench, then screw on the correct
injector selected from gas type category table
(last 3 pages in this user manual) according to
the gas to be used.
•Follow the above steps in the reverse order
after completing the assembly of the new
injector
Stand byAdjustment
Stand by adjustment for the cookers
without safety devices and with safety devices and button
ingition
•Turn the burner control knob to the small flame position and remove
the knob.
•If conversion from natural gas to LPG is required, turn clockwise the
by-pass screw of the gas valves with a screw driver to their final
position.
•If conversion from LPG to natural gas is required, turn anti-clockwise
the by-pass screw of the gas valves with a screw driver till a smaller
flame of¼size is obtained.
•After completing the adjustment, insert the knobs again.
•Check the adjustment by turning the burner control knob quickly from
maximum to minimum position. If the flame does not go out, it means
that the adjustment is correct.
•For safety devices, idle flame setting can be done with screw on valve
body. If there is ignition on the knob for idle flame setting cooktop,
toplid and panelmust be removed.
2
3
1
By-pass
screw for the burner
without safety
devices
Safety devices
GasOven
•Remove rear cover (Figure13)
•Remove injector adapter.(Figure 14)
• Remove injectors by using a 7 mm wrench, then screw on the correct
injector selected from gas type category table (last 3 pages in this
usermanual) according to the gas to be used. (Figure 15)
• Follow the above steps in the reverse order after completing the
assembly of the new injector
•BurnerGap is 4.5 + 0.3mmfor NGand LPG(Figure 16)
Figure 13
Figure 14
Figure 15
Figure 10
Figure 11
Figure 12
Figure16
Figure 17
Figure 18
Figure 19
Chart 3
4.5 + 0.3
9
10
11
14
15
13
12
16
17
18
17
18
19 GB
2.7.
TYPES
CONVERSION FOR DIFFERENT GAS
2.8. DIMENSIONS OF THE APPLIANCE
Height (mm)
Width (mm)
Depth (mm)
850
598
600
60 x 60
1-
2-
3-
4-
5-
6-
7-
8-
9-
10-
11-
12-
13-
14-
15-
16-
17-
18-
Cook top
Control panel
Drawer
Oven door (Front door)
Metallic top lid or Glass top lid
Auxilary burner
Rapid burner
Ultra rapid burner
Hot plate (1500W)
Left grate
Right grate
Burners control knobs
Hot plate control knob
Thermostat oven knob
Ignition button or fan button
Signal lamp
Moving Foot
Bolt Foot
2.9.
OF THE APPLIANCE
GENERAL APPEARANCE AND DEFINITION
This User Manual has been drawn up as a guide for several models.
Some of the properties mentioned in this manual may not exist in your
appliance.
1-
2-
3-
4-
5-
6-
7-
8-
9-
10-
11-
12-
13-
14-
15-
16-
17-
18-
Cook top
Control panel
Drawer
Oven door (Front door)
Glass top lid or metallic top lid
Auxilary burner
Rapid burner
Ultra rapid burner
Semi-Rapid burner
Left grate
Right grate
Burners control knobs
Thermostat oven knob
Ignition button or fan button
Lamp knob
Timer knob
Moving Foot
Bolt Foot
•For thermostat valve idle frame setting cooktop, top lid and panel
must be removed.
Содержание HCG6301PW
Страница 27: ......