4
GB
How to Replace
1.
To replace brushes, align post (h) on brush block with hole (i) on bottom of cleaner. Turn
brushes slightly until post fits easily into hole. Press brush assembly firmly to snap into
place.
[28]
2.
Return cleaner to upright position. Replace nozzle, making sure latches (d) are out. Align
middle section (e) of nozzle with opening (f ) on cleaner.
[26]
3.
While holding nozzle in place, slide latches inward to lock in.
[5]
IMPORTANT INFORMATION
Hoover spares and Consumables
Always replace parts with genuine Hoover spares. These are available from your local Hoover
dealer or direct from Hoover. When ordering parts always quote your model number.
Spares
Washable Filter
S116 35601336
Brush Block
F5
35601337
Hoover Service
Should any faults occur with your cleaner during the first 12 months contact the Hoover
Customer Helpline on the number below.
Quality
Hoover’s factories have been independently assessed for quality. Our products are made using
a quality system which meets the requirements of ISO 9001.
The Environment:
This appliance is marked according to the European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly you will help
prevent potential negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product.
The symbol on the product indicates that this product may not be treated as
houshold waste. Instead it shall be handed over to the appliance collection point
for recycling of electrical and electronic equipment. Disposal must be carried out
in accordance with the local environmental regulations for waste disposal. For
more detailed information about treatment, recovery and recycling of this product,
please contact your local city office, your household waste disposal service or the
shop where you purchased the product.
Your Guarantee
The guarantee conditions for this appliance are as defined by our representative in the country
in which it is sold. Details regarding these conditions can be obtained from the dealer from
whom the appliance was purchased. The bill of sale or receipt must be produced when making
any claim under the terms of this guarantee.
Subject to change without notice.
Should you have a problem with the product, complete this simple user checklist before calling
your local Hoover service.
PROBLEM
POSSIBLE CAUSE
SOLUTION
Cleaner
won’t run
t
Power cord not firmly plugged
in.
t
Plug unit in firmly
t
Blown fuse or tripped breaker
t
Check fuse or breaker in home.
Replace
Low suction
t
Washable filter is dirty.
t
Clean washable filter
t
Dirty water tank is full and the
auto shut off engaged.
t
Empty the dirty water tank
t
Tanks not in place
t
Make sure tanks are locked in
place.
t
Filter or filter lid not in place.
t
Make sure filter and filter lid are
properly positioned.
t
Nozzle not in place.
t
Make sure nozzle is replaced
properly and locked in place.
Water
puddling
behind
cleaner
t
Wrong detergent used.
t
Use recommended detergents
to reduce foaming.
t
Clean water solution tank not
in place.
t
Make sure clean water solution
tank is installed properly.
t
Dirty water tank full.
t
Empty dirty water tank.
Cleaner
won’t pick up
dirty solution
t
Dirty water tank not in place.
t
Make sure Dirty Water Tank is
installed properly.
t
Dirty water tank full.
t
Empty Dirty Water Tank.
t
Filter or filter lid not in place.
t
Make sure Filter and Filter lid are
properly positioned.
Cleaner
solution
won’t
dispense
t
Tanks not in place.
t
Make sure tanks are locked in
place.
t
Clean water solution tank is
empty.
t
Refill Clean Water Solution Tank.
Brushes
wont rotate
t
Blown fuse or tripped breaker.
t
Check fuse or breaker in home.
Replace fuse / reset breaker in
home.
t
If the brushes continue to stall
and the breaker trips again,
clean the brushes to remove
debris.
TROUBLESHOOTING
FloormateManual__1-4_union.indd 4
10/09/2012 14.00.12
