Hontzsch flowtherm Ex Скачать руководство пользователя страница 29

Страница: 29 / 34

_________________________________________________________________________________________________

______________________________________________________________________________________
U426_flowtherm Ex_B_e_171206

www.hoentzsch.com

29/34

Troubleshooting

Fault

Cause

Troubleshooting

Device cannot be
switched on

Dead batteries

Insert new batteries

Faulty electronics

Return to Höntzsch

No measured value
display
no value

Sensor contaminated

Clean according to instructions

Profile factor set at 0.000

Set profile factor to the corresponding value of
nominal diameter and sensor type

Unit setting (5.3.19.1) does
not correspond to the con-
nected flow sensor

Adjust the setting (5.3.19.1) to the connected
sensor or connect compatible sensor

Measured value too
low

Sensor type or KKZ set incor-
rectly

Compare and correct settings according to
details in the Technical Data Sheet

Sensor contaminated

Clean according to instructions

Profile factor set too low

Set profile factor to the corresponding value of
nominal diameter and sensor type

Input/output section too
short

Change sensor position; improve flow
conditions with a flow straightener

Rotational flow

Reposition sensor in flow direction; use flow
straightener

Vortex VA sensors:
reduced acoustic coupling in
the sensor elements as a
result of vibration or impact

Return sensor to Höntzsch for checking

Measured value too
high

Sensor type or KKZ set
incorrectly

Compare and correct settings according to
details in the Technical Data Sheet

Profile factor set too high

Set profile factor to the corresponding value of
nominal diameter and sensor type

EMC problem

See reference to electromagnetic compatibility
(EMC) in the sensor documents

Replacement Parts

battery compartment cover

connector socket cap

12-pin connector plug

DURACELL Simply MN1500 AA LR6 1.5V
1 Pack (4 pcs.), article-no. A000/007

Содержание flowtherm Ex



































Результаты поиска

Содержание flowtherm Ex

Отзывы:

Похожие инструкции для flowtherm Ex

Бренды по названию

Популярные бренды

Hontzsch flowtherm Ex, Руководство по эксплуатации

Результаты поиска

Содержание flowtherm Ex

Отзывы:

Похожие инструкции для flowtherm Ex

Бренды по названию

Популярные бренды