Honeywell WEB-O3022H Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 13

Honeywell WEB-O3022H Скачать руководство пользователя страница 13

Honeywell Building Technologies

Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
customer.honeywell.com

® U.S. Registered Trademark
© 2019Honeywell International Inc.
31-00319-02 | Rev 06-2020

Conformance statement

This digital apparatus complies with CAN ICES-003 (B)/ NMB-3 (B). This device complies with Industry Canada
license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harm-
ful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:

1.

Reorient or relocate the receiving antenna.

2.

Increase the separation between the equipment and receiver.

3.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

FCC Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation

«
...
11
12
13

Содержание WEB-O3022H














Отзывы:

Нет отзывов