manualshive.com logo in svg

Honeywell VS8421, Руководство по установке, Страница: 8 / 8

Поделиться
Скачать
Honeywell VS8421 Скачать руководство пользователя страница 8

69-1219—1   G.R.  Rev. 12-00 

www.honeywell.com

VS8421 VENTFREE MILLIVOLT GAS VALVE

Printed in U.S.A. on recycled 
paper containing at least 10% 
post-consumer paper fibers.

Home and Building Control Home and Building Control

Honeywell

Honeywell Limited-Honeywell Limitée

1985 Douglas Drive North

35 Dynamic Drive

Golden Valley, MN  55422

Scarborough, Ontario
M1V 4Z9

Fig. 7. Identification of VS8421 

terminals for troubleshooting.

Procedure:

1.

Test A (Coil Resistance): Have thermostat contacts 
open and Pilotstat knob turned to OFF. If coil 
resistance exceeds 3.6 ohms, replace the valve.

2.

Test B (Thermopile): Have thermostat contacts 
open and the pilot lit with Pilotstat knob turned to 
PILOT. If the reading is less than 460 mV, replace 
the thermopile.

3.

Test C (Thermocouple): Have thermostat contacts 
open and pilot lit with Pilotstat knob turned to 
PILOT. Reading should be a minimum of 12 mV in 
a new ODS pilot burner assembly. If the reading is 
less than 12 mV, replace the ODS pilot burner 
assembly. The power unit will hold in down to 3 
mV. If the output of the thermocouple is less than 3  
mV, replace the ODS pilot burner assembly.

4.

Test D (Operator Pull-In): have thermostat contacts 
open and pilot lit with Pilotstat knob turned to 
PILOT. Close the thermostat contacts. Operator 
will pull in with a minimum of 155 mV. Operator 
makes audible sound during pull-in. If pull-in does 
not occur, replace the valve.

5.

Test E (Resistance System): System resistance 
from the remote switch or thermostat and lead 
wires should not exceed 1.7 ohms. If resistance is 
above 1.7 ohms, reduce the resistance.

Table 2. VS8421 Troubleshooting Table.

M17559

WIRING TERMINALS

OFF

PILOT

ON

TPTH

TH

TP

Test

Test Title

Connect Multimeter 

Between Terminals

Set Thermostat

Meter Reading Should Be:

A

Coil Resistance

TP and TH

Open

Maximum of 3.6 ohms

B

Thermopile

TP and TPTH

Open

Minimum of 460 mV.

C

Thermocouple

Tip (and Ground)

Open

Minimum of 12 mV.

D

Operator Pull-In

TH and TP

Open

Minimum of 155 mV.

E

Resistance System

—

Closed

Maximum of 1.7 ohms.

69-1219-1.fm  Page 8  Thursday, August 18, 2011  7:32 AM

Содержание VS8421









Отзывы:

Нет отзывов